699577
26
Zoom out
Zoom in
Previous page
1/43
Next page
24 Installer Manual SATEL
The OUT4 and OUT5 outputs can also be used to control the NOKTON NR2-DSC radio
monitoring transmitter (NEMROD system format PC16OUT). In such a case it is necessary
to change the operating mode of these outputs by activating a suitable option in the service
function FS5. During operation with the NOKTON transmitter, the outputs are used for
transmitting a number of data on the control panel state (zone alarms, fire alarms, troubles,
armed mode, etc.) and do not perform functions programmed with the standard service
functions.
When hooking up any equipment with a considerable current consumption (e.g.
a radio monitoring transmitter) to the control panel, their "+" should be
connected to the battery "+" (a fuse is recommended on the feeder cable).
The ground must be connected to any COM contact of the control panel, but not
directly to the battery "-". Connection of the common ground to the battery "-"
causes incorrect operation of the charging current limiter and quick discharge
of the battery but can even damage the control panel.
Connections of telephone line
If the control panel telephone communicator is used in the alarm system (for monitoring,
messaging or remote programming), it is necessary to connect telephone line to the control
panel. It should be led to a connector situated on the right side of the printed board. In order
to ensure proper messaging, the control panel must be directly connected to the line
(connectors designated as TIP and RING), and any other devices (telephone, telefax) after
the control panel (connectors designated as T-1 and R-1). Such a connection will make it
possible for the control panel to fully engage the line for the time of calling, which prevents
the messaging function from being blocked by lifting the handset. Additionally, the telephones
connected after the control panel do not signal the dialing by the control panel.
Caution:
Do not send telephone signals and alarm system signals by one multicore cable. This may
result in a damage to the system in case of a high-voltage punch-through from the
telephone line.
Telephone terminals of the panel should be connected to PSTN lines only. Connecting to
ISDN lines may lead to damage of the equipment.
System installer should give the necessary information on the way of connection with
telephone network to system owner.
Connection of voice synthesizer
Where the function of alarm messaging with
voice announcements is used, a voice
synthesizer must be connected to the control
panel.
The CA-10 panel interfaces with the SM-2
synthesizer. The synthesizer socket
(designated as: SM-2 VOICE SYNTHESIZER)
is situated on the right-hand side of the
printed board, between the telephone line
connector and the socket of OUT5, OUT6
outputs. The SM-2 synthesizer should be
directly plugged into this connector. It is fitted
with minijacks for playback of the message
and "monitoring" of the telephone line.
ground
low-frequency signal
release
tel. line monitoring
power supply +
control panel
board
Figure 15. Description of SM-2 voice
synthesizer connector.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info