699577
32
Zoom out
Zoom in
Previous page
1/43
Next page
30 Installer Manual SATEL
FS45, FS46 station transmission formats in case of a multi-format station, select
format which is as fast as possible (e.g. Ademco Express or Radionics 2300 with parity).
FS47 – monitoring options.
FS48 to FS59 monitoring stations identifiers, an identifier should have 3 or 4 non-
zero characters (characters from 1 to F”, “0” – no character), some stations use
identifiers composed from digits from 0 to 9 – then character A is to be programmed
instead of digit “0” (e.g. “A1A2” instead of “0102”).
At least three identifiers should be programmed (can be identical):
zone identifier,
partition identifier,
system event identifier.
FS60 to FS66 & FS69 to FS72, FS81, FS82, FS126 event codes according to the list
from the monitoring station operator, the codes can be one-digit (the other character
being 0) or two-digit as required by the station, the codes with inappropriate length may
block communication with the station.
if reporting with event sorting to both stations has been selected in the options, events
assignment should be programmed in the functions FS67–FS68, FS73–FS80, FS83,
FS84.
FS5 – activate the option “Monitoring” after the above items have been programmed.
Typical problems with starting the monitoring:
Control panel takes no attempts to call not all of the above mentioned items have
been programmed the control panel will not call the monitoring station if the
programmed data do not allow sending a correct transmission to the station because of
e.g. missing telephone number, identifier being shorter than 3 non-zero characters,
missing event code, etc.
Problems with dialing no dial tone or a non-standard dial tone from the telephone
exchange find out the cause of missing signal or disable the dial tone test option in
FS5 if the signal is non-standard.
Control panel sends no codes when connected to the station wrongly selected
format or low quality of telephone connection (the panel does not “understand” the
station dial tone).
Station does not receive or acknowledge the codes sent by the panel – wrongly
selected format, inadequate identifier length (3 characters, while the station requires 4),
inadequate event code length (1 character, while the station requires 2) or low quality of
telephone connection.
Control panel does not send codes of some events, despite of the codes being
properly entered identifier of the particular group of events is missing, e.g., if the
partition 1 identifier is missing, no reports on this partition arming/disarming will be sent.
Control panel automatically changes the option „transmission to Station 1 or to
Station 2” into transmission to one station only if with this monitoring option
selected the number of identifiers for Station 1 and Station 2 is different (there are
codes which have an identifier for one station, but not for the other), the panel cannot
report to both stations in the „Station 1 or Station 2” mode and will change the option for
transmission to the station which has a larger number of identifiers.
Note: For the Ademco Express transmission format the identifier „0000” is correct (sending
"zero" is possible), while for the other formats it means no identifier ("zero" is not sent).
A headset connected to the "telephone line monitoring" jack in the SM-2 synthesizer can be
helpful in analyzing the problems with communication to the monitoring station.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info