520097
77
Zoom out
Zoom in
Previous page
1/119
Next page
77
GOAL of EXAMPLE: STEPS: INPUTS:
Adjust travels as needed to match
model’s recommended throws (usually
listed as high rates).P. 39.
In the
BASIC
menu, choose
END POINT
.
C
to
END POINT
.
to choose
END POINT
.
Adjust the servos’ end points.
(Ex: ap servo)
Close the function.
C
to
FLAP
.
VR(A) until travel as desired.
VR(A). Repeat as needed.
Set up dual/triple rates and exponential
(
D/R
,
EXP
)
P. 42.
(Note that in the middle of the left
sideof the screen is the name of the
channel and the SWITCH position
you are adjusting. Two or even three
rates maybe set per channel by simply
choosing the desired SWITCH and
programming percentages with the
SWITCH in each of its 2/3 positions.)
Choose
D/R
,
EXP
.
C
to
D/R
,
EXP
.
to choose
D/R
,
EXP
.
Choose the desired control, and set
the first (Ex: high) rate throws and
exponential.
C
to
CH>
.
to choose
CH>2
(elevator).
A to up position.
[Note screen reads
ELEV
(UP)
]
C
to
D/R
.
ELEVATOR STICK. to set.
ELEVATOR STICK. to set.
(Normally the same for both directions.)
C
to
EXP
.
ELEVATOR STICK. to set.
ELEVATOR STICK. to set.
Set the second (low) rate throws and
exponential.
C
to
D/R
. A to down position.
Repeat above to set low rate.
Optional: change dual rate SWITCH
assignment. Ex: elevator to SWITCH G
with 3 positions.
C
to
SW
. to
G
.
G to center position.
Repeat steps above to set 3rd rate.
Move ap control from the VR(A) dial
to the left slider [VR(D)]. (
AUX-CH
)
p. 46.
In the
BASIC
menu, open
AUX-CH
.
C
to
AUX-CH
. to choose
AUX-CH
.
Choose
CH6
( ap).
Change primary control to VR(D).
Change other channels as needed.
C
to
CH6
.
to
VR(D)
.
Repeat as required.
Return to the home screen.
Where next? (Other functions you may wish to set up for your model.)
TRAINER
p. 47.
Multiple wing or tail servos. See wing types and tail types: p. 51, 56.
OFFSETS
,
BUTTERFLY
(
AIRBRAKE
/crow), and other programmable mixes p. 61.
Retractable Gear, Smoke systems, kill switches, and other auxiliary channel
setups: p. 46.
Adjusting
SUB-TRIMs
to match servo centers: p. 49.
77


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FF-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FF-10 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FF-10

Robbe Futaba FF-10 User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info