520097
78
Zoom out
Zoom in
Previous page
1/119
Next page
78
A LOOK AT THE RADIO'S
GLID
-SPECIFIC FUNCTIONS STEP BY STEP.
Those functions which are identical to the
ACRO
setups are referred directly to those pages.
MODEL
TYPE
: This function of the
PARAMETER
submenu is used to select the type of model programming to be used.
GLIDER TYPES:
Before doing anything else to set up a glider or sailplane, rst you must decide which
MODEL
TYPE
best ts your aircraft.
ACRO
: for some aerobatic/slope gliders,
ACRO
is a better choice because of functions it offers that the
GLID
types do not.
ACRO
provides:
SNAP-ROLL
,
AILEVATOR
(twin elevator servo support),
AIRBRAKE
(a more assignable version of
BUTTERFLY
).
For nitro-powered sailplanes:
IDLE-DOWN
,
THR-CUT
,
THROTTLE-NEEDLE
mixing and
THROTTLE DELAY
programming.
• But
ACRO
lacks programming for full-span ailerons and separate OFFSET trims for each ight condition: Normal,
Start, Speed, Distance and Landing.
GLID(1A+1F)
: The
GLID(1A+1F)
MODEL
TYPE
is intended for sailplanes with one or two aileron servos (or none), and a single
ap servo (or two connected with a y-connector). This
TYPE
is meant to be a very simplistic version to set up a basic
glider without a lot of added features. Additional ight conditions available.
GLID(2A+1F)
: The
GLID(2A+1F)
MODEL
TYPE
is intended for sailplanes with dual aileron servos and a single ap servo (or
two connected with a y-connector) Additional ight conditions available. These ight conditions contain different offset
trims and aileron differentials to make the sailplane perform certain maneuvers more easily.
GLID(2A+2F)
: The
GLID(2A+2F)
MODEL
TYPE
supports dual flap servos that can also act as ailerons, creating full-span
ailerons and aps. Additional ight conditions available. These ight conditions contain different offset trims and aileron
differentials to make the sailplane perform certain maneuvers more easily.
GOAL of EXAMPLE: STEPS: INPUTS:
Change model1 is
MODEL
TYPE
to
GLID(1A+1F)
.
NOTE:
This is one of the several
functions that the radio requires
con rmation to make a change.
Confirm you are currently using the
proper model memory. (Ex: 1)
On home screen, check model nameand
number on top left.
If it is not the correct model (Ex: 1), use
MODEL SELECT
, p. 25.
Open
PARAMETER
submenu.
for 1 second.
(If
ADVANCE
, again.)
to 2nd page of menu.
C
to
PARAMETER
.
Change the
MODEL
TYPE
.
Con rm the change.
C
to
TYPE
. to
GLID(1A+1F)
.
for one second.
Are you sure?
Con rmation displays.
to con rm.
Close.
GLID(1A+1F)
(FLAPERON)
AIL1
FLP2
(CH1)
AIL2
FLP1
(CH6)
AIL1
(CH1)
AIL2
(CH7)
FLP
(CH6)
GLID(2A+1F)
AIL1
(CH1)
FLP1
(CH6)
FLP2
(CH5)
AIL2
(CH7)
GLID(2A+2F)
78


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FF-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FF-10 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FF-10

Robbe Futaba FF-10 User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info