520097
119
Zoom out
Zoom in
Previous page
1/119
Next page
119
Throttle trim adjustment: see
ATL
to change throttle trim from “idle only” to full trim control like all other channels. See
THR-REV
to reverse THROTTLE STICK completely, including moving trim to the top of the THROTTLE STICK. See
also Idle management for details on idle down and throttle cut functions.
TIMER
: adjust the timer functions, used to keep track of ight time on a tank of fuel, etc. The “trigger” to turn timers on/off
may be programmed. ........................................................................................................................................................... 45
TP-FM: single-frequency module. See Module.
TRAINER
: software that allows 2 radios to be connected via trainer cord, giving student control of all or some of the
channels of the aircraft at the ip of a switch.
FUNC
trainer mode allows student to use mixing in the master transmitter, for
example dual rates, exponential, y a 5-channel helicopter with a 4-channel buddy box, etc. ........................................... 47
Trainer box: stripped-down radio system which does not have the ability to transmit, is used only as a student’s radio when
instructing while using a trainer cord and the trainer programming.
Trainer cord: cord used to connect two compatible radios to use for ight instruction. See Accessories.
TRIM
menu: adjusts rate at which the trim responds to movement of the trim sliders. Also has a reset function to reset the
model’s electronic trims to zero. .......................................................................................................................................... 48
TRIM OFFSET
: (
HELI
) sets an offset or adjustment of trim when switching between conditions. See OFFSET.
TRIM
option in mixes: ability to adjust the slave servo’s center when the master servo’s center is adjusted using the trim
sliders (for example when using two separate ap servos). See Programmable mix. ........................................................ 61
Triple rate: 3rd control travel setting available in ight. See
D/R
,
EXP
.
Twin aileron servos: use of 2 or more servos on separate channels to control aileron action. Includes aperon, aileron
differential, and elevon. ....................................................................................................................................................... 51
Twin elevator servos: use of 2 or more servos on separate channels to control the elevator of a model. Includes elevon,
ailevator, V-tail. .................................................................................................................................................................... 58
Tx: transmitter.
Voltmeter, voltage reading: displays transmitter voltage on home screen. .......................................................................... 23
VR(A-E): variable rate controls. Knobs and sliders on the radio. See switch assignment chart for default assignments.
VR(A-C) are knobs; VR(D-E) are sliders on the case sides.
V-tail model Mix: (
ACRO
/
GLID
) programming used to control a V-tail model’s tail surfaces, with 2 servos operating 2
control surfaces as both rudder and elevator. See Twin elevator servos.
Warning messages: cautions provided by the radio when certain potential problems exist. See Error messages.
Warranty information. ............................................................................................................................................................ 3
Website: www.futaba-rc.com. Internet location of extensive technical information Futaba products. ................................. 3
Whip antenna: aftermarket, shortened antenna. Not approved by Futaba.
119


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FF-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FF-10 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FF-10

Robbe Futaba FF-10 User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info