520097
8
Zoom out
Zoom in
Previous page
1/119
Next page
8
MODULE: TP-FM/TM-10 2.4G
• Module may be easily removed and a module on a different channel (or even band) reinserted to change the frequency on
which the 10C transmits.
• TP-FM module transmits both FM (
PPM
) and
PCM
. No need for a second module. TM-10 2.4GHz module transmits both
2.4G-7ch
and
2.4G-10ch
.
All transmission circuitry is included in the module, so no retuning is needed when changing channels or even bands.
• Frequency band is changed by inserting a module on the proper band, including for international or ground model use.
• TP-72 FM module: In North America it is against FCC regulation to change the crystal within the transmitter module
to a different channel. All such transmitter crystal changes must be performed by a certi ed radio technician. Failure to
properly tune a system to its new channel may result in decreased range and may also result in interference to other types
of frequency users on adjoining channels. Doing so also voids your AMA insurance.
Non-Futaba brand modules are not FCC certi ed for use with this radio and therefore are against FCC regulation to use.
Doing so also voids your AMA insurance.
• The FSS synthesized module for the 9Z family of radios is NOT compatible with the 10C.
• Radio system beeps and RF LIGHT goes out to indicate module is not installed and radio is not transmitting.
• TP-75 FM modules may also be used with the 10C for ground use modules such as robotics, rocketry, trains, cars, and
boats.
RECEIVER: R138/R148/R1410/R6014FS
• The R138 or R148 FM 8-channel or the R138 PCM 8-channel or R1410 PCM 10-channel receiver included with your
system is a high-sensitivity narrow-band dual-conversion receiver. The R6014FS 2.4GHz 14-channel is FASST-2.4GHz
Multi-ch mode receiver.
• Note that your 10C transmitter with TP-FM module or TM-10 2.4G module is capable of transmission on both
PPM
(FM)
and
PCM
or on both
2.4G-7ch
and
2.4G-10ch
with just a simple programming change and just turning the transmitter off
and back on. (See p. 35.)
Any Futaba narrow band FM receiver (all produced after 1991) on the correct frequency band and frequency may be used
with the 10C.
Any Futaba PCM 1024 receiver on the right frequency band and frequency may be used with the 10C (all 1024 receivers
say PCM1024; receivers which say PCM but not 1024 are 512/2048 resolution and not compatible).
• Futaba FASST-2.4G R6014FS or R608FS receiver may be used with the 10C at
2.4G-10ch
mode. Futaba FASST-2.4G
R607FS or R617FS receiver may be used with the 10C at
2.4G-7ch
mode.
Transmitter
Receiver
R606FS
R616FFM, R607FS,
R617FS
R608FS, R6014FS
TM-14 Module
Multi-ch mode
——Okay
7ch mode Okay Okay
TM-10 Module
10ch mode Okay
7ch mode Okay
TM-8 Module
8ch mode Okay
7ch mode Okay
TM-7 Module Okay
T7C 2.4G System Okay Okay
FASST transmitter module, system
and receiver compatibility
• 72MHz band: NEVER attempt to change a receivers band by simply changing crystal (i.e. removing a 72MHz crystal
and inserting a 75MHz crystal). A receiver that has a crystal installed from a different frequency band without retuning
will not receive properly and will have dramatically decreased range.
In North America the receiver included with this system may have its frequency changed by simply changing the crystal
as long as it remains in the same half the band. A low band receiver between channels 11 and 35 may be changed to any
other channel between 11 and 35 without requiring any tuning. A high band receiver between channels 36 and 60 may
similarly be changed. Receivers being changed from a high band channel to a low band or vice versa require proper
tuning and service by the Futaba Service Center.
SERVOS
• Please see technical speci cations page for speci cs on the servos included with your system.
•The included receiver is compatible with all J-plug Futaba servos, including retract, winch, and digital servos.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FF-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FF-10 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FF-10

Robbe Futaba FF-10 User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info