815524
27
Zoom out
Zoom in
Previous page
1/40
Next page
27 7027-802M 04/23
D. Glass
Figure 27.1
Top & Bottom Frame
Door Latch
Side
Frame
Center Posts
Glass
Remove Door Latch First
and then Side Frame
Door Frame
shown with no
Glass or Glass
Frames
Remove 5 nuts from Bottom Frame
Figure 27.2
NOTE: DO NOT LET Air Wash Spacers fall down from
top frame when removing and replacing center glass.
NOTE: When removing the side glass with the door latch,
you must remove the door latch rst before removing the
side frame. Use a powered Phillips head screw driver to
remove the 4 screws.
PART NUMBERS:
LEFT OR RIGHT SIDE GLASS: 510-5400
CENTER BAFFLE: 510-5410
Remove door from appliance and place face down on a
protected surface to avoid scratching the door.
Remove all door rope.
a. Be sure the appliance is allowed to cool, has been
unplugged and the exhaust blower is o󰀨.
b. Remove side glass frame.
c. Loosen the top and bottom frame and slightly bend
up and out of the way.
d. Slide glass out the side and slide new glass in.
e. Re-install the side glass frame and tighten the top
and bottom frames.
f. Re-install the door latch, if applicable, and re-rope
the door.
2. Side Glass
1. Center Glass
a. Be sure the appliance is allowed to cool, has been
unplugged and the exhaust blower is o󰀨.
b. Using a nut driver remove the (5) bottom nuts and
remove the bottom glass frame (Figure 27.1).
c. Slightly bend up and out of the way the 2 center posts
and slide the glass out the bottom.
d. Slide new glass in, reposition the 2 center posts and
re-install bottom glass frame.
e. Re-rope the door.
Glass is 5mm thick high temperature heat-
resistant ceramic glass.
DO NOT REPLACE with any other material.
Alternate material may shatter and
cause injury.
WARNING
Handle glass assembly with care.
When cleaning glass:
CAUTION
Avoid striking, scratching or slamming glass.
Do NOT clean glass when it is hot.
Do NOT use abrasive cleaners.
Use a hard water deposit glass cleaner on white lm.
Refer to maintenance instructions.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire Classic Bay 1200 Pellet at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Classic Bay 1200 Pellet in the language / languages: English as an attachment in your email.

The manual is 5.89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Classic Bay 1200 Pellet

Quadra-Fire Classic Bay 1200 Pellet User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info