Manual Quadra-Fire Classic Bay 1200 Pellet (page 26 of 40) (English)

815524

Zoom out

Zoom in

1/40

26 7027-802M 04/23

Igniter

Igniter Bracket

Thumb Screw

Figure 26.1

B. Ba󰀪es

PART NUMBERS: LEFT BAFFLE: 510-5350, RIGHT

BAFFLE: 510-5360

1. Use proper shut down procedures to shut down the

appliance and let it completely cool down.

2. Open right side panel and then open the door.

3. The 2 ba󰀪es are located at the top inside of rebox.

4. Place your hand on the ba󰀪e and slide it up and the

bottom edge will fall down and then you can lift the ba󰀪e

out. Repeat for the other side.

a. Remove Ba󰀪e to Access Heat Exchanger Tubes

and Firebox Exhaust Exits

i. Open the upper right side panel door and then

open the glass door.

ii. The 2 ba󰀪es are located at the top inside of rebox.

iii. Place your hand on the ba󰀪e and slide it up and

the bottom edge will fall down and then you can lift

the ba󰀪e out. Repeat for the other side.

iv. Re-install in reverse order.

C. Igniter

PART NUMBER: SRV7000-462

1. Use proper shut down procedures to shut down the

appliance and let it completely cool down and then

unplug it and remove the ash drawer.

2. Follow instructions to remove the ash pan found on

page 18 - Cleaning Ash Pan. Remove the access plate

directly above it by removing the 2 screws just below the

ash catcher.

3. The wire leads to the igniter are connected to the wire

harness with 1/4 inch male / female spade connectors.

These wires will pull forward approximately 4 to 5 inches

(102mm to 127mm). Disconnect the spade connections

and remove the igniter from the chamber. Loosen the

thumb screw and slide igniter out.

4. Install new igniter into the chamber and tighten the

thumb screw. Re-connect the wires to the 2 leads with

the spade connectors.

5. Remove right side panel and pull wire leads back toward

the rear of the appliance to take-up the 4 to 5 inches

(102mm to 107mm) previously pulled out. This will keep

the wires out of the way of the ash drawer. Double check

that the igniter wires are clear of any movement, i.e. ash

drawer, re pot cleaning rod, etc.

6. Re-install the ash drawer and side panel and re-connect

the power.

Shock Risk.

• Do NOT remove grounding prong

from plug.

• Plug directly into properly grounded 3

prong receptacle.

• Route cord away from appliance.

• Do NOT route cord under or in front

of appliance.

CAUTION

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Classic Bay 1200 Pellet in the language / languages: English as an attachment in your email.

The manual is 5.89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Classic Bay 1200 Pellet

Quadra-Fire Classic Bay 1200 Pellet User Manual - French - 40 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Quadra-Fire Classic Bay 1200 Pellet Manual

Product: