782211

Proxxon FET Manual

16
Zoom out
Zoom in
Previous page
1/24
Next page
adjustment of the longitudinal stop“) at the knurled
screw 6 (fig. 10d).
Caution!
Make sure the mains plug is disconnected for all ad-
justing work!
1. Make sure that locking handle 3 and knurled screw
4 are released.
2. Move the longitudinal stop 1 with the left edge 6
over the „0“ marking of the scale (either left or
right from the saw blade, depending on what is
needed for the task) as shown in fig. 10d and fix
the position by tightening knurled screw 4.
3. By turning the fine adjustment knob 7 bring the
scale with its arrested longitudinal stop into the
position where the side of the longitudinal stop
facing the saw blade just barely touches the saw
blade. Please carefully lift the saw blade guard 8 to
do so, if necessary!
Now the distance between the saw blade and limit
stop is „0“ as shown by the scale.
The limit stop can now be aligned with the help of
the scale, as described in the section „Adjusting the
longitudinal stop with the help of the scale“: The
value read from the scale now corresponds exactly
to the distance longitudinal stop – saw blade and
thus the desired width of the work piece.
Caution!
It is possible that before adjustment in the zero posi-
tion, the scale is in a position where the longitudinal
stop already touches the saw blade before the left
limit stop edge has reached the „0“ position on the
scale. In this case simply correct the scale position
with the fine adjustment knob 7.
Fine adjustment of the longitudinal stop
If after the sawing process it is necessary to make
minor changes to the position of the limit stop (de-
spite previous careful adjustment) to achieve the de-
sired width, it is possible to move the limit stop for a
small amount in the desired direction with the fine
adjustment knob 7, see fig. 10d. Please note: One
complete revolution will move the limit stop by 1 mm!
Caution! For this procedure, the lock handle 3 must
be released, but the knurled screw 4 must be tight-
ened. After adjustment is completed, the limit stop
must be tightened with locking handle 3 to continue
sawing!
Auxiliary stop
Appropriate use of the auxiliary stop is made to be
able to easily cut somewhat larger work pieces as
well. For this, the saw table must be extended first,
as described in the chapter „Extendable saw table“;
but the limit stop edge is not „sunk“ in the extend-
able part by „pressing in“ but simply stays outside.
The distance to the saw blade determines the sawing
width, which can therefore be varied depending on
by how much the saw table is pushed in, or ex-
tended. To saw, always fix the limit stop by tightening
the knurled screw. See fig. 8a.
Angle stop
If it is necessary to cut a board at right angles, or a
strip with mitre cut, then this can be sawn by using
the angle stop. This runs in the guides provided ei-
ther on the right or on the left of the saw blade, as re-
quired.
1. Insert the angle stop in the guide 1 to the right or
left of the saw blade, see fig. 11.
2. Release knurled screw 2, set the desired angle at
the scale 3 and retighten the knurled screw.
Working with the limit stop strip with
clamping piece for angle stop
Ideal, e.g. if many strips will be cut with mitre and
equal length, see fig. 12. The limit stop strip is con-
nected to the angle stop 2 to do this. The clamping
piece 3 is used as length stop.
Assembly and adjustment
Push the limit stop strip 1 into the guide of the angle
stop 2 (see fig. 13a) and insert together in the guide
in the saw table. Caution! The knurled screw must be
in the „released“ position otherwise the limit stop
cannot be inserted.
16
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon FET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon FET in the language / languages: English as an attachment in your email.

The manual is 1.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info