782211
18
Zoom out
Zoom in
Previous page
1/24
Next page
This is very well suited for most „sawing jobs“, guar-
antees clean cuts in the most various materials and
guarantees long service life. But it will not last for
ever, of course: Wear will occur depending on the in-
tensity of use: The saw blade will become dull, more
force to push the work piece is required and the
quality of the cut is reduced, the mechanics of the
machine are stressed more strongly than necessary.
Then it is high time to replace the saw blade with a
new one. It can also be necessary to use a different
saw blade type for a particular task (see also the
chapter „Choosing the right saw blade“ below) so
that it needs to be exchanged for the standard blade.
The work steps remain the same, naturally.
1. Disconnect the mains plug!
2. Turn the saw blade down as described in the
chapter „Height adjustment of the saw blade“.
3. Swing open the housing as described in section
„Swinging open the upper housing part“.
4. To release the screw 1 (fig 16a), the shaft on which
the saw blade 2 is mounted must be blocked. To
do so, insert the smaller of the two included Allen
keys 3 through the small drill hole 4 in the saw
table and from there insert it into the saw blade
shaft through a cross-hole, see fig. 16b. If neces-
sary, this drill hole must be „found“ somewhat by
turning the saw blade by hand. A hint: For this pro-
cedure we recommend you adjust the saw blade
to a relatively high height and then to lower it
somewhat after finding the latching drill hole with
inserted Allen key in order to gain full access to
screw 1.
5. Release the hexagon-head screw 1 with the larger
of the two Allen keys and remove together with
disc 5.
Caution!
The teeth of even worn saw blades are still very
sharp! Risk of injury!
6. Remove the old saw blade upwards and through
the saw blade opening and place the new saw
blade on the shaft. Make sure the saw blade drill
hole is seated correctly at the shaft shoulder!
7. Please also make sure that the teeth are pointing
in the direction as shown in the figures!
8. Screw on disc 5 with the hexagon-head screw 1
and tighten. Note that the saw shaft still needs to
remain blocked with the small Allen key.
9. Release the latch, push down the upper housing
part and lock with the knurled screw.
Choosing the right saw blade
Caution!
When choosing the saw blade, make sure at all costs
that the highest permissible speed is sufficiently high
enough for the idling speed of the saw!
Only use original Proxxon saw blades.
The choice of the suitable saw blade has an enor-
mous impact on the work result: Various characteris-
tics such as work piece material, saw job intensity
and the desired quality of the result must be consid-
ered. Proxxon has 4 different saw blades that can be
used to operate the machine:
18
Super-Cut
Ø 85 x 0.5 x 10 mm,
Suitable for more soft woods and plastics
Article number 28 731
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon FET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon FET in the language / languages: English as an attachment in your email.

The manual is 1.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info