782211

Proxxon FET Manual

17
Zoom out
Zoom in
Previous page
1/24
Next page
1. To adjust the angle, release knurled screw 4 and
set the desired value at the scale 5. Retighten
knurled screw 4. Adjust position of limit stop strip
1 and clamp firmly by tightening the knurled screw
6.
2. Caution! Make sure at all costs that the limit stop
strip 1 is correctly seated in the receiver of the
angle stop 2 and that there is sufficient distance
from the end of the limit stop strip to saw blade 7!
In all cases: Switch off the saw and disconnect the
mains plug and test to see that the limit stop strip
does by no means touch the saw blade or the saw
blade guard, see fig. 13c!
3. Insert clamping piece 8 in the guide of the limit
stop strip (fig. 13d) and determine the position in
dependence on the desired work piece length.
Please note: The hexagon nut travels in the guide
of the limit stop! Fix the clamping piece with the
knurled screw 9.While sawing, the piece to be
sawn is pushed up to the limit stop and can be
crosscut as shown in fig. 12.
Sawing
Caution!
Your FET may not be used for slitting (notch com-
pleted in the work piece)! To groove or notch, please
by all means use the Proxxon groove-milling device
(article number 28736).
Hold the work piece on the saw table as shown in
fig. 14. Adapt the feed according to the material, the
saw blade and the work piece thickness! Hard mate-
rials, fine saw blades and thick work pieces do not
“tolerate” as much feed as soft materials, rough saw
blades and thin materials.
Always operate the saw from the position as shown
in Fig. 14a so that you are always in optimal control
of the work piece. Stand in front of the saw while
sawing! Never saw with your FET from the side or
even from the back. Ensure sufficient stability while
you work!
If you process correspondingly small work pieces
then use the included push-rod, as shown in fig. 15.
This prevents your hands from coming to close to the
revolving saw blade and thus reduces the risk of in-
jury:
Always keep the push-rod close to hand while work-
ing!
If the device is not in use, please use the supplied
push-rod in the designated housing fixture (fig. 14b)!
Please note:
• Only use perfect saw blades.
• Always remove the mains plug for maintenance
and upkeep work.
• Do not let the device operate unsupervised.
When sawing, press the work piece onto the work
plate, guide with sensitivity and with little force, more
pressure on the work plate, less pressure against the
saw blade. Guide the work piece slowly into the saw
blade, particularly if the blade is very thin and the
teeth very fine or if the work piece is very thick.
General tips on sawing
For good results, please note the following points:
• When sawing, press the work piece onto the work
plate, guide with sensitivity and with little force;
more pressure on the work plate, less pressure
against the saw blade.
• Make sure that the work piece is lying properly on
the saw table (no burrs or sawdust)
• Adapt the feed to the requirements by saw blade,
speed and work piece material.
• Guide the work piece slowly into the saw blade,
particularly if the blade is very thin and the teeth
very fine or if the work piece is very thick.
• Only use perfect saw blades.
• Do not let the device operate unsupervised.
• Carefully mark out the check line.
• Make sure there is good lighting.
• Always work with connected dust suction!
• If necessary, use the included push-rod to feed the
work piece.
Changing the saw blade
Your saw is equipped with a carbide-tipped saw
blade with 24 teeth and an 80 mm diameter ex
works.
17
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon FET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon FET in the language / languages: English as an attachment in your email.

The manual is 1.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info