782211

Proxxon FET Manual

15
Zoom out
Zoom in
Previous page
1/24
Next page
Dust suction
At the back of the housing of your FET you will find a
connecting piece for dust suction, see fig. 9: a vac-
uum cleaner is connected here.
This should always be operational while working! Not
only because it guarantees a clean working environ-
ment, but also because this prevents the interior of
the saw from becoming contaminated from sawdust.
The vacuum cleaner hose is simply connected to the
rubber adapter, as shown in the picture 9a.
Another small tip:
When using the Proxxon CW-matic vacuum cleaner,
manual switching on and off is no longer necessary.
The CW-matic is equipped with an automatic control
that switches on and off automatically whenever the
electrical tool is activated or deactivated.
Working with the limit stops
Working with the longitudinal stop
Longitudinal stops are indispensable working aids for
producing any number of work pieces with exactly
the same width (or length) without having to mark the
piece to be sawn each time. The material to be sawn
is simply guided along the longitudinal stop with
slight pressure during the sawing procedure. The
measure of the finished sawn work piece thus corre-
sponds to the distance of saw blade and limit stop
edge.
If necessary, you can refer to the scale at the front of
the housing to adjust the longitudinal stop.
The future measure of the work piece can be read off
from a marking. However, the scale must be adjusted
exactly to the saw blade beforehand – therefore „ze-
roised“. How this is done is described below.
The scale is dimensioned for the use of the limit stop
on both sides of the saw blade. The most various
sawing tasks are therefore no problem.
Inserting, or removing, the longitudinal
stop
The longitudinal stop 1 (fig. 10a) is inserted, or re-
moved, from the side (from the right or left) in the
guide 2 at the saw table. While you are shifting, in-
serting, or removing the longitudinal stop make sure
that both fixing options locking handle 3 and knurled
screw 4 are released! The scale 5 was attached with
restricted rotation. Please make sure it is properly
seated when you insert the limit stop.
Rough adjustment of the longitudinal
stop
The rough adjustment simply by shifting the longitu-
dinal stop without using the scale 5 (fig. 10b) is suffi-
cient for many cases.
When you shift the longitudinal stop, please make
sure that both fixing options locking handle 3 and
knurled screw 4 are released!
Once the desired position is achieved, the longitudi-
nal stop is arrested by tightening the knurled screw 4
and then clamped with the locking handle 3.
Adjusting the longitudinal stop with the
help of the scale
1. When you shift the limit stop, please make sure
that the locking handle 3 and knurled screw 4 are
released.
2. The longitudinal stop can now be shifted in its
guide using the help of the scale 5. The position
can be read from the left front limit stop edge 6,
see fig. 10 c. Caution: The read value will only
agree if the „zero position“ of scale 5 is correct!
How to correctly adjust the zero position of the
scale is described in the section „Adjusting the
limit stop scale“.
3. Arrest the longitudinal stop by tightening knurled
screw 4 and then clamping the locking handle 3.
Adjusting the limit stop scale
(zero position)
For the reliable use of the scale 5 for the longitudinal
stop, its position must first be co-ordinated to the
saw blade – therefore „zeroised“. This process is ab-
solutely necessary after the saw blade has been re-
placed with a saw blade of different thickness, or if
the limit stop was finely adjusted (see section „Fine
15
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon FET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon FET in the language / languages: English as an attachment in your email.

The manual is 1.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info