782211
14
Zoom out
Zoom in
Previous page
1/24
Next page
1. Swing open the upper housing part and arrest.
2. Please note that the saw blade in its delivered
condition is in the lower position to guarantee ac-
cessibility to the drive unit. Otherwise, please pro-
ceed as explained in the section "Height
adjustment of the saw blade".
3. If the two screws 1 (fig. 5a) are not loose, please
release them slightly with a screwdriver. Insert the
orange-coloured saw blade guard with the splitting
wedge 2 in the saw blade slot 3 and insert behind
the little plate clip 4 like shown in Fig. 5). Please
ensure correct fit: The splitting wedge is seated on
the upper of the two screws 1 with its longer cut-
out (fig. 5a) up to the limit stop! Make sure the
splitting wedge is fitted correctly in any case! Only
tighten both screws 1 afterwards! After you have
tightened the screws, please check once more if
the splitting wedge is seated firmly and if the saw
blade can be turned freely.
4. Push the upper housing part back down and se-
cure with the knurled screw.
5. Set the desired saw blade position as described
further down in the chapter "Height adjustment of
the saw blade".
Settings
Height adjustment of the saw blade
To adapt the depth of cut, the position of the saw
blade can be regulated in the height. On the one
hand, this optimises the sawing performance, and on
the other hand the risk of injury is reduced due to the
restriction of the free saw blade part.
Caution!
Make sure the mains plug is disconnected for all ad-
justing work!
1. Release the larger knurled button 1 (fig. 6) at the
front operating plate and unscrew by a few revolu-
tions
2. The saw blade position can now be set using the
smaller knurled button 2: Turning clockwise will
adjust the blade upwards, and turning counter-
clockwise will adjust the blade downwards.
3. After the desired position is achieved, retighten the
knurled button 1.
Adjusting the saw blade tilt
The saw blade can be tilted to manufacture mitre
cuts. The desired value is set, or read, with the help
of the angle scale.
Caution!
Make sure the mains plug is disconnected for all ad-
justing work!
1. Release handwheel 1 (fig. 7).
2. Swing the saw blade to the right with the hand-
wheel.
3. Set or read off the desired angle with indicator 2 at
the angle scale 3.
4. Arrest the saw blade position by turning the hand-
wheel 1 shut
Extendable saw table
Caution!
Make sure the mains plug is disconnected for all ad-
justing work!
In order to place larger work pieces easily and se-
curely on the saw table, it has been designed as an
extendable saw table. The extension is quite simple:
Please note:
1. Use your finger to push the curry-coloured limit
stop edge 1 (fig. 8a) towards the back. This makes
it move out upwards.
2. Pull out the saw table 2 with the limit stop edge
into the desired position, see fig. 8b. If necessary,
support with the swivelling lever 3.
3. The small knurled screw 4 can be used to clamp
the extendable saw table into the desired position,
as necessary.
4. Now push the limit stop edge 1 back into its initial
position to achieve a plane surface. It is now pos-
sible to work with the saw. Please note: The limit
stop edge can also be used for larger work pieces
as a longitudinal stop, of course.
5. After completing your work, simply push the ex-
tendable saw table 2 back into the initial position.
If necessary, fold up the swivelling lever 3 before.
14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon FET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon FET in the language / languages: English as an attachment in your email.

The manual is 1.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info