782211
13
Zoom out
Zoom in
Previous page
1/24
Next page
Setting up the saw
Unpacking
Caution!
Please note that transport blocks have been at-
tached to the device during packing to avoid dam-
age during transportation. Make sure you remove all
of them before commissioning! Carefully read
through the instructions and especially observe the
following chapter!
A transport block made of cardboard is inserted on
the inside of the saw. This must be removed before
initial commissioning. How to swing up the upper
housing part is explained in the following chapter.
Swinging open the upper housing part
1. Please open the packaging box to unpack, care-
fully remove the saw and deposit it on a firm and
level surface.
2. Release the knurled screw 1 (fig. 2) and swing up
the upper housing part 2.
3. Permit the latch 3 to engage.
4. Before first commissioning, remove the cardboard
that was used as safeguard during the transport.
5. Release the latch 3 of the support and push the
upper housing part back down. Caution! Hold on
to the upper part when pushing down! Injuries
might be caused if the upper part drops down
unchecked.
6. Retighten knurled screw 1.
Fastening the saw
Generally the saw must be set up on a fixed and
level surface, ideally on a heavy workbench or a solid
table. To obtain a secure hold, your FET should be
screwed to the surface: For this purpose there are
four holes in the housing bottom so that fastening
screws can be screwed into them.
Note:
Safe and precise work is only possible with careful
fastening! Therefore, please proceed as follows:
Caution!
Make sure the mains plug is disconnected!
1. Swing up the upper part of the saw
2. Permit the latch to engage
3. Now you can see four hexagonal indentations on
the inside above the four screw holes in the hous-
ing bottom, see fig. 3. These are intended to re-
ceive M6 hexagon nuts, or the heads of M6 (or
similar) hexagon screws. Insert sufficiently long
screws 2 from inside through the opening in the
housing bottom and bolt them through the drill
holes that you previously drilled in the underlay 3.
1. Use a drilling template for the required hole spac-
ing. You will find a sketch with the dimensions at
fig. 4.
4. Then release the latch of the support and push the
upper housing part back down.
5. Do not forget to tighten the knurled screw 1 (fig. 2)!
Saw blade guard
Your FET is equipped with a saw blade guard. It is
designed in such a way that moves up as far as nec-
essary during sawing and then drops back into its
home position. It also adapts to the various adjusted
cutting depths.
Caution!
The saw blade guard is an important safety tool and
may in no way be tampered with or even dismantled.
Operating the saw without this guard is dangerous!
While setting up and transporting the saw, always
may sure that the upper saw blade cover is in its cor-
rect position. The free-lying, sharp teeth of the saw
blade pose a considerable risk of injury!
Secure the saw blade guard with the
splitting wedge (Fig. 5 and 5a)
Caution!
For packaging reasons, the saw blade guard and the
splitting wedge are not attached when the device is
delivered. However, assembly is rather simple:
Caution!
Make sure the mains plug is disconnected!
13
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon FET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon FET in the language / languages: English as an attachment in your email.

The manual is 1.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info