Manual Pride Colt Deluxe 2.0 (page 34 of 44) (English)

722005

Zoom out

Zoom in

1/44

Mid-size Scooter Series

Any electromechanical device occasionally requires some troubleshooting. However, most of the

problems that may arise can usually be solved with a bit of thought and common sense. Many of these

problems occur because the batteries are not fully charged or because the batteries are worn down and can

no longer hold a charge.

DIAGNOSTIC FAULT CODES

The diagnostic beep codes for your Scooter are designed to help you perform basic troubleshooting

quickly and easily. A diagnostic beep code will sound in the event one of the conditions listed below

develops. Depending on the model you own, your scooter will communicate by one of the coding meth-

ods as follows:

1. A beep code will begin with a series of fast beeps directly followed by slower beeps which indicates

the actual code. The beep code is only beeped once. To repeat the beep code, remove the key, then

reinsert it and turn it on to the “on” position, OR

2. A beep code will identify the condition, pause, then repeat the beep code. The beep code will continue

to alert you in this manner until the scooter is turned off.

NOTE: Your scooter will not run unless the fault code condition is resolved and the scooter has been

turned off, then turned back on

FAULT CODE CONDITION SOLUTION

 (1)

Battery charge is low. Charge batteries as soon as possible.

  (2)

Battery charge is too low. Charge batteries.

   (3)

The scooter's battery voltage is too

high to operate the scooter, or the

charger is still connected to the off-

board charger port.

Unplug charger and/or turn key off,

then back on again.

    (4)

Current limit time out. Turn the scooter off for a few

minutes, then turn your scooter

back on.

     (5)

The manual freewheel lever is in the

(forward) freewheel position.

Remove the key from the key

switch, then push the manual free-

wheel lever to the drive (rearward)

position and restart your scooter.

      (6)

Throttle control lever not at center

position at start up.

Verify that the batteries are fully

charged. If the batteries are fully

charged, then return the throttle

control lever to center position, turn

scooter off then back on.

       (7)

Speed pot error. Call your authorized Provider for

assistance.

        (8)

Motor volts error. Call your authorized Provider for

assistance.

        

(9)

Other internal errors. Call your authorized Provider for

assistance.

VII. BASIC TROUBLESHOOTING

I bought a 'new' Pride Colt Deluxe 2.0. Later I discovered that both Track Rods where they fit on the Track Rod Ends as best as I could see has some play in them. I rang up the Shop who supplied it, & they sent someone out with a Tie Rap, & then put one on each of them to hold them firmly together. My question is, is this standard procedure when dealing with Mobility Scooters, or are they manufactured 'disabled' to be like the Owner ? Submitted on 3-10-2024 at 20:35
Reply Report abuse
Console shows three green lights are out while charger is flashing fully charged Submitted on 15-10-2023 at 15:01
Reply Report abuse
How do I enable the scooter to go from pushing to driving mode? Submitted on 1-7-2023 at 19:42
Reply Report abuse
Why is my suspension on my pride deluxe Colt so tight Submitted on 21-9-2021 at 11:28
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pride Colt Deluxe 2.0 in the language / languages: English as an attachment in your email.

The manual is 2,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pride Colt Deluxe 2.0 Manual

Product: