722005

Pride Colt Deluxe 2.0 Manual

32
Zoom out
Zoom in
Previous page
1/44
Next page
32
Mid-size Scooter Series
VI. DISASSEMBLY AND ASSEMBLY
1 2
4 5 6
3
DISASSEMBLY
You can disassemble the scooter into several pieces: the seat, the rear section, the front section, the basket,
the batteries, and the battery shroud. See figure 21. No tools are required to disassemble or assemble your
scooter, but keep in mind that the disassembled sections of the scooter take up more floor space than the
assembled unit. Always disassemble or assemble your scooter on a level, dry surface with sufficient room
for you to work and move around your
scooter—about
5 feet (1.5 meters) in all directions. Remember that
some scooter components are heavy and you may need assistance when lifting them.
WARNING! Do not lift beyond your physical capability. Ask for assistance when
necessary while disassembling or assembling your scooter.
Figure 21. Disassembled scooter
IDENTIFICATION KEY
1. SEAT
2. REAR SECTION
3. FRONT SECTION
4. BASKET
5. BATTERIES
6. BATTERY SHROUD
Figure 22. Tiller Lock Knob (Model 104
only)
Disassembly Procedures
1. Remove the key from the key switch. For model 104, lock the
tiller in the straight ahead position by pushing the tiller lock
knob in and turning it clockwise 90°. See figure 22. The front
wheel must face forward in order to lock the tiller.
2. Remove the seat by lifting it straight up and off of the scooter.
If you encounter resistance when removing the seat, disengage
the seat rotation lever and swivel the seat back and forth while
lifting up on the seat.
3. Gently pull the battery shroud forward, then lift up and off of
the scooter. See figure 10.
4. Disconnect the battery tie-down strap. See figure 11.
5. Unplug both battery harnesses by depressing the tabs and then
pulling each harness straight up. See figure 11.
6. Remove the batteries from the battery wells.
WARNING! Failure to unplug both battery
harnesses prior to separating the front and rear
sections could result in permanent damage to
the scooter.
7. For model 104, you also need to disconnect both front-to-rear
harnesses. See figure 11.
WARNING! Failure to unplug both front-to-rear
harnesses prior to separating the front and rear
sections could result in permanent damage to
the scooter.
NOTE: Please check the Scooter Features Table on the inside of the front cover to determine if your
scooter has a frame release lever or a lockup pin before attempting to separate the frame.
… 32 …


Need help? Post your question in this forum.

Forumrules
1

Forum

pride-colt-deluxe-2.0

Reset search

  • I bought a 'new' Pride Colt Deluxe 2.0. Later I discovered that both Track Rods where they fit on the Track Rod Ends as best as I could see has some play in them. I rang up the Shop who supplied it, & they sent someone out with a Tie Rap, & then put one on each of them to hold them firmly together. My question is, is this standard procedure when dealing with Mobility Scooters, or are they manufactured 'disabled' to be like the Owner ? Submitted on 3-10-2024 at 20:35

    Reply Report abuse

  • Console shows three green lights are out while charger is flashing fully charged Submitted on 15-10-2023 at 15:01

    Reply Report abuse

  • How do I enable the scooter to go from pushing to driving mode? Submitted on 1-7-2023 at 19:42

    Reply Report abuse

  • Why is my suspension on my pride deluxe Colt so tight Submitted on 21-9-2021 at 11:28

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pride Colt Deluxe 2.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pride Colt Deluxe 2.0 in the language / languages: English as an attachment in your email.

The manual is 2,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info