584558

Philips DVP-620VR Manual

9
Zoom out
Zoom in
Previous page
1/20
Next page
Decoder allocation
Some TV channels transmit encoded TV signals which can only
be viewed with a purchased or rented decoder.You can
connect such a decoder to this DVD/VCR.The following
function will automatically activate the connected decoder for
the desired TV channel.
1 Switch the TV on. If applicable, select the programme number
for the DVD/VCR operation.
2 Press K/L or numerical key pads to select the TV channel
which you would like to allocate
the decoder to.
3 Press DISC/VCR MENU.The main
menu will appear.
4 Press K/L to select “TUNER SET
UP”.Then press B.
5 Press K/L to select “MANUAL
TUNING”.Then press B.
6 Press K/L to select “DECODER”.
7 Press B to select “ON” (Decoder switched on).
8 To end, press STATUS/EXIT.
The decoder has now been allocated to this programme
number.
9
English
Setting the RF out channel
In some reception locations it is possible that a TV channel will
be sent on the same or similar frequency as the DVD/VCR.
Result:As soon as the DVD/VCR is switched on, the reception
quality for this or several other TV channels will decrease.
The following steps will show you how to change the pre-set
'transmission' (RF out channel) frequency on the DVD/VCR.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select “INITIAL SET UP”, then press B.
3 Press K/L to select “RF OUT”,
then press B.
4 Press B.
5 Press K/L or numerical key pads
to select a free (not allocated)
channel between channel 22 and 69
in your area.
6 Press B.
7 To end, press STATUS/EXIT.
SELECT KL CHOOSE B
→RF OUT CH 36
END=EXIT
What is RF out channel?
This electronic component in the DVD/ VCR allows the device to
transmit audio and video signals via the aerial cable.These signals
can be received on a TV set just like TV channels.
What is RF out channel frequency?
This frequency or channel indicates the channel on which the
audio or video signal is transmitted.
If you cannot get an interference-free picture and sound, connect
the DVD/VCR and the TV with a scart cable.Then, switch the
built-in modulator off.
Press L repeatedly until “--” appears next to “RF OUT CH” on
the TV screen.
Then confirm with B.
How can I switch off the decoder?
Use B to select “OFF” (Decoder switched off).
MANUAL TUNING
PROG. P55
CHANNEL 055
→ DECODER [OFF]
SKIP [OFF]
SELECT KL CHOOSE B
END=EXIT
Time/date is displayed incorrectly despite manual setting
With Smart Clock, time/date is taken from the TV channel saved
on “P01”.
If you wish to switch this automatic time correction off, select
“OFF” for Smart Clock.
You can reactivate this function at anytime by selecting “ON” for
Smart Clock.
VCR Playback
4 Check the time in “TIME”.
If required, please change the time with numerical key pads.
5 Check “DAY”,“MONTH” and “YEAR” in the same way.
6 Choose “SMART CLOCK ON” or “OFF” with B.
7 To end, press STATUS/EXIT.
DIGITAL STUDIO PICTURE CONTROL
Philips has developed a system which produces the best possible
playback quality. For old and often-used video cassettes, this system
reduces interference. For new or high quality cassettes,
it emphasises the details.
Picture/ sound quality is poor
When playing back rental videos or older, poorer quality cassettes,
it may not be possible to completely filter out picture and sound
interference.This is not a fault in your machine. Read the section
Manual Tracking.
Do I need to change the playback speed when playing
back LP recordings?
During playback, the correct speed will automatically be selected.
For more information, please read the section Selecting the
recording speed (SP or LP) in the chapter VCR Manual
Recording.
Playing back NTSC cassettes
This DVD/VCR can also playback cassettes that have been
recorded in SP [Standard Play] or SLP [Super Long Play] mode
in the NTSC standard (for example,American cassettes).
However, this only works on PAL-television sets that are
suitable for a picture frequency of 60Hz.
Displaying current tape position
The following information is displayed on the screen:
e.g.: “0:02:45” shows the counter in hours, minutes and
seconds.
“SP/LP” will show the recorded speed of your cassette
“REM 0:06” will show the remaining time left on the tape in
hours and minutes.
When you playback an NTSC cassette, the DVD/ VCR will
show “REM -:--”.
How can I set the counter to “0:00:00”?
You can set the counter to “0:00:00” with CLEAR.
When you put a cassette in the DVD/VCR, the counter will
automatically reset to “0:00:00”.
The counter does not move
This occurs when there are no recordings on a portion of a tape.
This is not a fault in your DVD/VCR.
The screen shows “-0:01:20”
If you rewind a cassette from the tape position “0:00:00”, the
counter will show for instance,“-0:01:20” (the cassette was
rewound to 1 minute and 20 seconds before “0:00:00”).
“-:--” is displayed in the “REM” counter
This counter will automatically recognise the length of the tape.
In addition, when you put in a cassette the DVD/VCR will first
calculate the time played.Therefore,“-:--” appears first and only
after the tape has been running for a few seconds, the correct
remaining time will be shown.
Playing back video cassettes
You can operate the DVD/ VCR using the remote control or the
buttons on the front of the DVD/VCR. If you press PLAY B,
STOP C,
h
or
g
while the set is in Stand-by, the power will
be automatically turned on.Additionally, if a cassette was already
inserted, the corresponding operation will be performed.
Your DVD/VCR can only record and playback standard VHS
cassettes.
1 Put a cassette into the cassette slot.The cassette is inserted
automatically.
2 Press PLAY B to view the tape.‘ B ’ will appear on the display.
3 To stop the playback, press STOP C or STOP/EJECT A on the
DVD/VCR.
4 To eject the cassette, press EJECT A or STOP/EJECT A on
the DVD/VCR when the DVD/VCR stops the playback.
H9720ED.qx3 04.4.16 10:43 AM Page 9
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips DVP-620VR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips DVP-620VR in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Philips DVP-620VR

Philips DVP-620VR User Manual - German - 20 pages

Philips DVP-620VR User Manual - Dutch - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info