584558
7
Zoom out
Zoom in
Previous page
1/20
Next page
Turning on your DVD/ VCR
The following steps only be performed when you insert the AC
PLUG at the first time.
1 Turn on the TV and select the
video channel on the TV.
2
Plug in the DVD/VCR.
3 Press K/L repeatedly to select
your desired language.
4 Press DISC/VCR MENU.
5 Confirm with P+.
The automatic TV channel search
starts.
6 “TIME” and “DATE” will appear on
the TV screen.
7 Check “TIME”. If required, please
change the time with numerical key
pads.
8 Check if the displayed settings for
“DAY”, “MONTH” and “YEAR” are
correct.
9 When all information is correct,
save by pressing STATUS/EXIT.The
preparation for use is now
complete.
Note:
When AUTO TUNING has been completed, the initial
settings menu will not appear even if the AC plug has
been unplugged or after a power failure.To recall this
initial settings menu, press SOURCE and PLAY at the
same time for more than 2 seconds on the system’s
front panel.
Playable Video Cassette Tapes
Philips Consumer Electronics recommends that only video
cassette tapes that have the VHS mark and High Quality (HQ)
system is compatible with this DVD/VCR.This
DVD/VCR has an Automatic Head Cleaner.
Recording Prevention
Video cassette tapes have record tabs to
ensure recordings are not erased accidentally.
1 To prevent recording, break off the tab with a
screw-driver.
2 To allow recording, cover the hole with
cellophane tape.
Notes:
– Use only tapes with VHS mark.
– Remove any adhesive stick-on notes from the tape
before inserting into the DVD/VCR.
– Periodic maintenance is required to maintain your DVD/
VCR performance.
Video heads will require replacement after a period of
time. Only an authorised service center should perform
this service.
Using the Remote Control
• Direct the remote control at the remote sensor of the DVD/
VCR.
• Do not drop the remote control.
• Do not leave the remote control near extremely hot or
humid place.
Do not spill water or put anything wet on the remote control.
Inserting batteries into the Remote Control
1 Open the battery cover.
2 Insert batteries (AA size) with the
correct polarity as indicated by the
+
and - symbols inside the battery
compartment.
3 Close the cover.
CAUTION!
– Remove batteries if they are exhausted or not to be used
for a long time.
– Do not use old and new or different types of batteries in
combination.
– Batteries contain chemical substances, so they should be
disposed off properly and kept away from children.
External Input Mode (for VCR features)
To r eceive the signal from an external input (decoder, satellite
receiver, video camera, another VCR etc.), connect to the AV2
(DECODER) socket, and enter ‘0.0.2.’ with numerical key pads
to appear “AV2” on the TV screen.
If you use the AV1 (TV) socket, enter ‘0.0.1.’ with numerical key
pads to appear “AV1” on the TV screen.
If you use the front AUDIO/VIDEO in jacks, enter ‘0.0.3.’ with
numerical key pads to appear “AV3” on the TV screen.
7
English
Setting Up your DVD/ VCR
1
2
PLEASE WAIT
START FINISH
❚❚❚❚❚❚❚❚❚❚❚
❚❚❚❚❚❚❚❚❚❚❚❚❚
SELECT KL
ENGLISH
FRANÇAIS
ESPAÑOL
DEUTSCH
ITALIANO
SVENSKA
NEDERLANDS
PUSH MENU TO CONTINUE
Video Channel Setting
Video channel setting will be necessary, if your DVD/VCR is
connected to the TV via the coaxial cable.
1 Insert a pre-recorded tape into the DVD/VCR.The DVD/VCR
will turn on and start playback automatically.
If playback does not start, press PLAY B .
2 Select and adjust your TV to channel 36.
• If the playback picture appears on the TV screen, continue
with step 8.
• If channel 36 is employed for broadcasting, or interference
lines appear on the picture, the RF converter must be set to
a different channel between CH22 and CH69. Continue with
step 3.
3 Press DISC/VCR MENU.
4 Press K/L to select “INITIAL SET
UP”.Then, press B.
5 Press K/L to select “RF OUT”.
Then, press B twice.
6 Press K/L to select a channel
which is not used for broadcasted
between channel 22 and channel 69
in your area, then press B.
You can also see the selecting RF channel in the display
7 Press STATUS/EXIT to exit.
Set the TV channel to the RF OUT CHANNEL which was
selected on the DVD/VCR. A picture from the VCR will appear
on the TV screen. If a picture does not appear, repeat steps 3
to 7 using a different channel which is not used for
broadcasted.
8 Press STOP C to stop the tape.
Note:
You may also access the RF OUT CH menu by pressing
and holding DISC/VCR MENU for 3 seconds during
power off until the RF OUT CH menu appears.
SELECT KL CHOOSE B
RF OUT CH 36
SET=0-9
END=EXIT
TIME 10:00
DATE 25/ 12/ 04
SMART CLOCK [ON]
END=EXIT
H9720ED.qx3 04.4.16 10:43 AM Page 7
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips DVP-620VR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips DVP-620VR in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Philips DVP-620VR

Philips DVP-620VR User Manual - German - 20 pages

Philips DVP-620VR User Manual - Dutch - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info