Manual Parkside PTK 2000 D3 - IAN 298657 (page 29 of 108) (English, German, Dutch, Portuguese, Spanish)

691162

Zoom out

Zoom in

1/108

GB IE

Angle Adjustment

(Figure 29 and 3)

With the table circular saw it is possible to make bevel cuts to

the left at an angle of 0° to 45° to the stop rail. Before each cut,

make sure that no collision is possible between the stop rail (39),

cross-cutting gauge and the saw blade (4).

- Release the locking handle (9)

- Turn the handwheel (11) to set the desired angle on the

scale (10).

- Lock the locking handle (9) in the desired angular position.

Adjusting the Laser

(Figure 32)

If the laser (35) no longer shows the correct cutting line, this can

be readjusted. To do this, open the screws (z). Adjust the laser

so that the laser beam hits the cutting teeth of the saw blade (4).

Tighten the screws (z) again.

Using the Laser

(Figures 31-32)

- The laser (35) enables you to carry out precision cuts with

your circular saw.

- The laser light is produced by a laser diode supplied by two

batteries. The laser light is expanded to form a line and is

emitted through the laser exit aperture. You can then use the

line as an optical marking for the cutting line of the precision

cut. Please note the laser safety information.

- Insert the batteries

- Switch on the laser: turn the laser on/off switch (36) to I.

When the saw blade guard (2) is mounted, the laser on/off

switch (36) is accessible through a recess in the guard (Fi-

gure 31). A red laser beam is now projected out of the laser

exit aperture. If you guide the laser beam along the cutting

line mark while sawing, you will achieve clean cuts.

- Switch the laser off: turn the laser on/off switch (36) to 0.

The laser beam goes off. Please always turn the laser off

when it is not required in order to save the batteries.

- The laser beam may be blocked by dust deposits and chips.

You should therefore remove these particles from the laser

exit aperture after every use (with the device switched off).

Use

Working Instructions

After each new adjustment, we recommend a trial cut in order to

check the set dimensions. After the saw has been switched on,

wait until the saw blade has reached its maximum speed before

you carry out the cut.

Secure long workpieces against tilting at the end of the cutting

process (e.g. unwinding stand etc.)

Caution with incision cutting.

Operate the device only with a suction system. Check and clean

the suction channels regularly.

Suitability of the saw blades:

- 24 teeth: soft materials, high chip removal, rough cut image

 

Performing Longitudinal Cuts

(Figure 33)

Here, a workpiece is cut in its longitudinal direction. One edge

of the workpiece is pressed against the parallel stop (6) while the



always be lowered onto the workpiece. The working position du-

ring longitudinal cutting must never be in a straight line with the

cutting line.

- Adjust the parallel stop (6) according to the workpiece height

and the desired width.

- Switch on the saw.

 

workpiece and push the workpiece along the parallel stop

(6) into the saw blade (4).

- Guide from the side with your left or right hand (depending

on the position of the parallel stop) only up to the front edge

of the saw blade guard (2).

- Always push the workpiece through to the end of the riving

knife (3).

- The cutting waste remains on the saw table (1) until the saw

blade (4) is back in its resting position.

- Secure long workpieces against tilting at the end of the

cutting process! (e.g. unwinding stand etc.)

Cutting narrow Workpieces

(Figure 34)

Longitudinal cuts of workpieces with a width of less than 120

mm always have to be cut with the help of a push stick (19). The

push stick is included in the scope of delivery. Replace a worn or

damaged push immediately.

• Adjust the parallel stop according to the planned workpiece

width.

• Advance the workpiece with both hands, making sure that

you use a push stick (19) as a pushing aid in the vicinity of

the saw blade.

• Always push the workpiece through to the end of the riving

knife.

Caution! In the case of short workpieces, the push

stick should be used from the beginning of the cutting

process.

Cutting very narrow Workpieces

(Figure 35)

For longitudinal cuts of very narrow workpieces with a width of

30 mm and less, a push block must be used without fail. There is

no push block included in the scope of delivery! (Available from

specialist shops) Replace a worn push block as soon as possible.

• The parallel stop should be adjusted to the cutting width of

the workpiece.

• Press the workpiece with the push block against the stop rail

and push the workpiece with the push stick (19) through to

the end of the riving knife.

Motor cut out is there a restart button on the motor Submitted on 7-4-2023 at 16:16
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTK 2000 D3 - IAN 298657 in the language / languages: English, German, Dutch, Portuguese, Spanish as an attachment in your email.

The manual is 2,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PTK 2000 D3 - IAN 298657 Manual

Product: