Manual Parkside PTK 2000 D3 - IAN 298657 (page 30 of 108) (English, German, Dutch, Portuguese, Spanish)

691162

Zoom out

Zoom in

1/108

GB IE

Performing Bevel Cuts

(Figure 36)

All bevel cuts are made using the parallel stop (6).

- Adjust the saw blade (4) to the desired angle.

- Adjust the parallel stop (6) according to the workpiece width

and height.

- Perform the cut according to the workpiece width

Performing Transverse Cuts

(Figures 29, 37)

- Push the transverse stop (40) into one of the two grooves

(33) of the saw table. Adjust to the desired angle. The left

groove (33) is to be used if the saw blade (4) also has to be

positioned at an oblique angle.

This will prevent your hand and the transverse stop from

coming into contact with the saw blade guard.

- Use the stop rail (39).

 

- Switch on the saw.

- Push the transverse stop (40) and workpiece in the direction

of the saw blade in order to perform the cut.

 

the free workpiece which is cut off.

- Always push the transverse stop (40) so far forwards until the

workpiece is completely cut through.

- Switch the saw off again. Only remove sawing waste when

the saw blade has come to a standstill.

Cutting Chipboard

In order to prevent the cut edges chipping when the chipboard

is cut, the saw blade (4) should be adjusted so that it is not more

than 5 mm above the thickness of the workpiece.

Collection bag for wood residues

The collection bag is only intended for small wood residues. They

can be collected directly from the saw table to keep it clean and

free from obstructions. Under no circumstances may the wood

residues in the collection bag protrude beyond the collection bag

itself. This would prevent the saw table from being fully usable.

This poses a security risk.

Transport

(Fig. 38/39)

1. Turn the power tool off before it is transported and discon-

nect it from the power supply.

2. Pull off any suction hose, that may be connected, from the

suction adapter (18).

3. Insert the saw blade with the help of the crank handle (12).

By turning the saw blade (4) anticlockwise, it moves

downwards.

4. At least two people should carry the power tool. Do not hold

the power tool by the table width extensions. Please only use

the points as shown in (Fig. 38/39) to transport the

machine.

5. Protect the power tool against knocks, jolts and strong vibra-

tions, e.g. when it is transported in motor vehicles.

6. Secure the power tool against tilting and sliding.

7. Never use the protective devices for handling or transport.

Cleaning and Servicing

Remove the mains plug before carrying out any adjust-

ments, maintenance or repair work.

You should have any repair and maintenance work that is

not described in these instructions carried out by our Ser-

vice Centre. Only use original parts.

Perform the following cleaning and maintenance work regularly.

This guarantees reliable use for a long time.

Cleaning

The device must not be sprayed with water or

placed in water. Otherwise there is a risk of

electric shock.

• Keep the safety devices, air vents and motor housing as free

of dust and dirt as possible. Wipe the device off with a clean

cloth or blow it out with compressed air at a low pressure.

• We recommend that you clean the device immediately after

every use.

• Clean the device regularly with a damp cloth and some soft

soap. Do not use any detergents or solvents; these might attack

the plastic parts of the device. Make sure that no water can get

into the interior of the device.

• Oil the moving parts once a month in order to extend the tool

life. Do not oil the motor.

Storage

• Store the appliance in a dry place well out of reach of

children.

Waste disposal and environmental

protection

Take the batteries out of the device and recycle the device, bat-

teries, accessories and packaging in an environmentally friendly

manner.

Electrical machines do not belong with domestic waste.

• Dispose of the batteries according to local standards. Hand

in the batteries at a used battery collection point where they

are recycled in an environmentally friendly manner. For more

information, please contact your local waste management

provider or our service centre.

• Defective units returned to us will be disposed of for free.

Motor cut out is there a restart button on the motor Submitted on 7-4-2023 at 16:16
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTK 2000 D3 - IAN 298657 in the language / languages: English, German, Dutch, Portuguese, Spanish as an attachment in your email.

The manual is 2,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PTK 2000 D3 - IAN 298657 Manual

Product: