Manual Parkside PTK 2000 D3 - IAN 298657 (page 28 of 108) (English, German, Dutch, Portuguese, Spanish)

691162

Zoom out

Zoom in

1/108

GB IE

Operation

Switching on and off

(Figure 3)

- The saw can be switched on by pressing the green pushbut-

ton „I“. Before you start sawing, wait until the saw blade has

reached its maximum speed.

- In order to switch the saw off again, the red pushbutton „0“

has to be pressed.

Adjusting the Cutting Depth

(Figure 3)

By turning the crank handle (12), the saw blade can be set to the

desired cutting depth (continuous).

- Clockwise: increases the cutting depth

- Anticlockwise: reduces the cutting depth

Adjust the saw blade so that it protrudes approximately 5

mm above the material to be cut. Check the adjustment by

means of a test cut.

Working with the Parallel Stop

Adjusting the Stop Height

(Figures 22 and 24)

- The stop rail (39) of the parallel stop (6) has two guide

surfaces at different heights.

- Depending on the thickness of the materials to be cut, the

stop rail (39) has to be used differently. For thin material

(workpiece thickness less than 25 mm), use Figure 22. For

thick material (workpiece thickness more than 25 mm), use

Figure 24.

Turning the Stop Rail

(Figures 22-24)

 

nuts (m).

- Now the stop rail (39) can be pulled off the guide rail (16)

and pushed back over it again with the groove.

- Tighten the knurled nuts (m) again.

Adjusting the Cutting Width

(Figures 25-26)

- When wooden pieces are being cut lengthwise, the parallel

stop (6) has to be used.

- The parallel stop should be mounted on the right-hand side

of the saw blade (4).

- Insert the parallel stop into the side of the guide rail (16)

(Figure 26).

- On the guide rail for the parallel stop (6) there are 2 scales

(o/n). These show the distance between the stop rail (39)

and saw blade (4) (Figure 25).

- Select the suitable scale according to whether the stop rail

(39) has been turned around for working with thick or thin

material:

High stop rail (thick material): scale (o)

Low stop rail (thin material): scale (n)

- Adjust the parallel stop (6) to the desired level on the sight



Adjusting the Stop Length

(Figure 27)

- In order to prevent the material being cut from jamming, the

stop rail (39) can be moved in the longitudinal direction.

- Rule of thumb: the rear end of the stop abuts on an imagi-

nary line. This begins at about the middle of the saw blade

and runs towards the back at an angle of 45°.

- Adjust the required cutting width.

- Release the knurled nuts (m) and push the stop rail (39)

forward until the imaginary 45° line is touched.

- Tighten the knurled nuts (m) again.

Adjusting the Parallel Stop

(Figure 28)

- Caution! Remove the guard.

- Adjust the saw blade (4) to the maximum cutting depth.

- Adjust the parallel stop (6) such that the stop rail (39)

touches the saw blade (adjustment for thick material.

- If the parallel stop (6) is not parallel to the saw blade (4),

please proceed as follows. Release the screws (r) on the

parallel stop until the parallel stop (6) can be aligned to be

parallel with the saw blade (4) (Figure 28).

- Retighten the screws (r).

Transverse stop

(Figure 29)

- When the wood is being cut to size, the transverse stop (40)

must be extended with the stop rail (39) of the parallel stop

(6) (Figure 29)

- Push the transverse stop (40) into a groove (33) of the saw

table.

- Loosen the knurled screw (34).

- Turn the transverse stop (40) until the desired angle is set.

The notch on the guide bar shows the angle that has been

set.

- Retighten the knurled screw (34).

- In order to extend the transverse stop (40) with the stop rail

(39), the stop rail (39) has to be removed from the parallel

stop (6). Now the stop rail has to be mounted as shown in

Figure 29; use the knurled nuts (m) for this purpose.

Caution!

- Do not push the stop rail (39) too far in the direction of the

saw blade.

- The distance between the stop rail (39) and saw blade (4)

should be approximately 2 cm.

Adjusting the scale of the parallel stop

(Figure 30)

- Check whether the display on the sight glass (p) of the

parallel stop (6) shows the correct values with respect to the

cutting line. If this is not the case, please proceed as follows:

- Release the screw (q) with which the display on the sight

glass (p) of the parallel stop (6) is attached. The sight glass

(p) display can now be set to the correct position.

- Now, retighten screw (q) on the sight glass (p).

Motor cut out is there a restart button on the motor Submitted on 7-4-2023 at 16:16
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTK 2000 D3 - IAN 298657 in the language / languages: English, German, Dutch, Portuguese, Spanish as an attachment in your email.

The manual is 2,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PTK 2000 D3 - IAN 298657 Manual

Product: