Manual Parkside PTK 2000 D3 - IAN 298657 (page 27 of 108) (English, German, Dutch, Portuguese, Spanish)

691162

Zoom out

Zoom in

1/108

GB IE



device.

- Do not place the batteries on radiators or expose them for a

prolonged period to strong sunlight; temperatures above

45 ° could damage the device.

2. Initial mounting of the laser module:

- Mount the laser using the two Phillips head screws (z),

Fig. 15.

(Figures 16-20)

3. Adjust the saw blade (4) to a max. cutting depth, move to

the 0° position and lock in place.

4. Dismantle the saw blade guard (2)

(not during initial assembly).

5. Release the two attachment bolts (28) and remove the table

insert.

 

AF8 supplied).

7. Push the riving knife (3) upwards.

8. The distance between the saw blade and riving knife (3)

should be between 3 mm and max. 5 mm, (Figure 18).

9. Retighten the attachment bolts (29) and mount the table insert

(5).

10. Reattach the saw blade guard (2).

Mounting / dismounting

the Saw Blade Guard

(Figures 19)

-

de protection has already been carried out in

the previous assembly step.

1. Loosen the knurled nut and wing nut (31) of the saw blade

guard (2). Place the saw blade guard (2) from the top onto

the riving knife (3).

2. Mount the bolt with the knurled nut and washer (31) so that



3. Do not overtighten the bolt (31). The saw blade guard must

be able to move freely.

4. Dismantling is carried out in reverse order. Caution! Before

you start sawing, the saw blade guard (2) has to be lowered

onto the item being sawn.

Replacing the Table Insert

(Figures 16 and 20)

1. If it is worn or damaged, the table insert (5) has to be repla-

ced, as otherwise there is an increased risk of injury.

2. Remove the 2 countersunk screws (28).

3. Take out the table insert (5).

4. The new table insert (Order-Nr.: 91104566) is mounted in

reverse order.

Attaching/changing the Saw Blade

(Figure 21)

1. Caution! Remove the mains plug and wear protec-

tive gloves.

2. Dismantle the saw blade guard (2).

3. Remove the table insert (5) by releasing the two countersunk

screws (28).

4. Place the hexagon socket key (h) (HX 6) on the bolt and use the

jaw spanner (k) (SW 22) to stop the motor spindle from turning.

5. Caution! Turn the bolt in the direction of rotation of the saw

blade. Remove the loosened screw.

 



 

before attaching the new saw blade.

8. Insert and tighten the new saw blade in reverse order.

Caution! Note the direction of motion; the slope of

the cutting edge of the teeth must face the directi-

on of motion, i.e. forwards (see the arrow on the

saw blade guard.

9. Reattach and adjust the table insert (5) and the saw blade

guard (2).

10. Before you work with the saw again, a check must be

carried out to ensure that the protective devices are working

properly.

Connect the suction device

(Fig. 14)

1. Attach a suction hose to the suction adapter (18). If

necessary, secure the suction hose with a hose clamp to

prevent it from slipping off the suction adapter (18).

2. A household vacuum cleaner is not suitable as a suction de-

vice. Use a multi-purpose vacuum cleaner or a swarf extracti-

on machine.

Before putting into operation

• The machine must be set up on a stable surface, i.e. on the

base or similar item. For this, use the drill holes which are

located in the frame of the machine. For safe use on a work

bench, four mounted rubber feet are provided



• Before the machine is put into operation, all covers and safety

devices must be properly attached.

• The saw blade must be able to move freely.

• In the case of wood which has already been worked with,

check for foreign bodies such as nails or screws etc.

• Before pressing the on/off switch, make sure that the saw bla-

de is correctly attached and that moving parts are free-running.

• Before connecting the machine, check that the data on the

type plate matches those of the mains system.

• The machine must only be connected to a properly installed

safety socket which is protected by a fuse of at least 16A.

• If possible, connect the device only to a socket with a residual

current circuit breaker (RCCB) with a tripping current of not

more than 30 mA.

 

 

Motor cut out is there a restart button on the motor Submitted on 7-4-2023 at 16:16
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTK 2000 D3 - IAN 298657 in the language / languages: English, German, Dutch, Portuguese, Spanish as an attachment in your email.

The manual is 2,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PTK 2000 D3 - IAN 298657 Manual

Product: