Manual Parkside PTK 2000 D3 - IAN 298657 (page 25 of 108) (English, German, Dutch, Portuguese, Spanish)

691162

Zoom out

Zoom in

1/108

GB IE

risk of injury.

8 Before using any of the tools, ensure that all protective de-

vices are correctly attached.

 

technical requirements of this power tool and are properly

attached.

10 The saw blade supplied should only be used for sawing

wood and never for working metal.

Assembly and Attachment

of Tools and Tool Parts

a) Tools and tool bodies must be tightened in such a way that

they cannot become loose during operation.

b) Attachment bolts and nuts are to be tightened to the torques



c) Extending a spanner or tightening with the help of hammer

blows is not permitted.

d) The tightening surfaces must be cleaned to remove any dirt,

grease, oil and water.

e) Tensioning bolts must be tightened in accordance with the

manufacturer‘s instructions.

f) In order to adjust the borehole diameter of circular saw



inserted rings, e.g. rings which have been pressed into place

or which are held in place by means of an adhesive bond,

may be used. The use of loose rings is not permitted.

 

one another.

Safety Instructions

for Handling the Laser

– Caution: Laser radiation - Do not look into the beam - Laser

class 2

– The label is attached to the saw blade guard (2) near the

laser (34).

Safety Instructions

for Handling Batteries

1 Ensure at all times that the batteries are inserted with the

correct polarity (+ and –), as shown on the battery itself.

2 Do not short-circuit the batteries.

3 Do not charge up rechargeable batteries.

4 Do not overcharge the battery!

5 Do not mix old and new batteries or batteries of a different

type or from different manufacturers! Replace all batteries of

a set at the same time.

6 Remove used batteries immediately out of the device and

dispose of them correctly!

7 Do not heat the batteries!

8 Do not carry out any welding or soldering work directly to

the batteries!

9 Do not take the batteries apart!

10 Do not deform the batteries!

 

12 Store the batteries out of the reach of children.

13 Do not allow children to replace the batteries without supervi-

sion!

 

sources of heat. Do not place the battery in direct sunlight

and do not use or store it in motor vehicles in hot weather.

15 Store used batteries in the original packaging and keep them

away from metal objects. Do not mix (up) unpacked batte-

ries! Otherwise this may cause the battery to short-circuit,



16 Remove batteries from the device if this is not going to be

used for a prolonged period, unless it is to be used in emer-

gencies!

17 NEVER touch batteries which have leaked without appro-

priate protection. If the leaked liquid comes into contact with

the skin, you should rinse off this area of the skin immedia-

tely under running water. Make sure at all events that your

eyes and mouth do not come into contact with the liquid. If

they do, seek medical advice immediately.

18 Clean the battery contacts and the equivalent contacts in the

device before inserting the batteries.

Residual Risks

This power tool has been constructed in accordance

with the latest technology and the generally recog-

nised safety regulations. Nevertheless, it is possible

that individual residual risks may occur during opera-

tion.

• Electrical hazard if improper electrical connection cables are

used.

• In addition, concealed residual risks may be present in spite

of all the precautions that have been taken.

• Residual risks can be minimised by observing the „Safety

instructions“ and „Use in accordance with the designated

purpose“, as well as the operating instructions.

• Do not put any unnecessary stresses on the machine: exces-

sive pressure during sawing will quickly damage the saw

blade. This may result in a reduction in the performance of

the machine, as well as a reduction in the cutting accuracy.

• Avoid switching the machine on by accident: when inserting

the plug into the socket, the power button must not be pressed.

• Use the tool which is recommended in this manual. This will

ensure the optimal performance of your saw.

• Keep your hands away from the working area when the

machine is in operation.

• Before you carry out any adjustments or servicing work, turn

the device off and remove the mains plug.

Electrical Connection

The installed electric motor is connected ready for

operation. The connection complies with the relevant

VDE and DIN regulations. The customer‘s network

connection and any extension cable used must com-

ply with these regulations.

• The product meets the requirements of EN 61000-3-11 and

is subject to special connection conditions. This means that

its use at freely selectable connection points is not permitted.

• If the network conditions are unfavourable, the device may



• The maximum permitted mains impedance at the electrical

connection point of 0.107 ohm must not be exceeded.

• As the user, you must ensure – in consultation with your

electricity supply company if necessary – that the continuous

current carrying capacity of the network at the connection

Motor cut out is there a restart button on the motor Submitted on 7-4-2023 at 16:16
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTK 2000 D3 - IAN 298657 in the language / languages: English, German, Dutch, Portuguese, Spanish as an attachment in your email.

The manual is 2,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PTK 2000 D3 - IAN 298657 Manual

Product: