Manual Parkside PPS 40 B2 - IAN 327358 (page 18 of 49) (English, German)

763020

Zoom out

Zoom in

1/49

18 GB/IE/NI

• Using the device

• Operation

1. Set the plasma cutter 1 up in a dry and

well ventilated area.

2. Position the machine in the vicinity of the

workpiece.

3. Press the on/off switch 17.

4. Clamp the ground terminal 4 to the

workpiece to be cut and make sure that

there is a good electrical contact.

5. Set the cutting current on the current

controller 13. If the arc beam is inter-

rupted the cutting current must be set

higher if necessary. If the electrode burns

through frequently, then the cutting

current must be set lower.

6. Position the plasma cutter 8 on the

workpiece so that the burner sleeve 8c is

free and that a blowback of the molten

metal is not possible. Press the plasma

burner button 8a. The transmitted cutting

arch is ignited on the edge of the sheet

in this manner.

7. Start cutting slowly and then increase the

speed in order to achieve the desired

cutting quality.

8. The speed must be regulated so that a

good cutting capacity can be achieved.

The plasma beam creates a straight arch

(stainless steel, aluminium) or a 5° arch

of approach (soft steel).

To cut in the manual cutting mode,

pull the overlying burner across the

workpiece while maintaining a

constant speed. To achieve the perfect cut, it

is important for the material thickness to

comply with the correct cutting speed. If the

cutting speed is too low, the cutting edge will

be blunt due to the severe heat input.

The optimal cutting speed is achieved once

the cutting jet is slightly inclined towards the

rear while cutting. If the plasma burner

button 8a is released, the plasma jet goes

out and the power source switches off. The

gas continues to flow for approx. 5 seconds

in order to cool the burner. The same

process is followed when the workpiece is

pulled out with a pressed plasma burner

button 8a. During the gas post-flow time,

the plasma cutter 1 must not be switched off

to avoid damaging the plasma burner 8 as

a result of overheating.

ATTENTION!

fThe device must be left on for approx.

2-3 minutes once the cutting work has

been completed. The cooler cools the

electronics.

• Types of plasma cutting

Drag cutting

Hold the tip of the burner sleeve

low over

the workpiece and press the plasma burner

button

. Now move the burner sleeve until

there is contact with the workpiece and

the cutting arch is fixed. Once the cutting

arch has been generated, move the plasma

burner

in the desired direction. Makes

sure that burner sleeve is slightly

angled

and that contact with the workpiece is

maintained. This working method is called

drag cutting. Avoid quick movements. A sign

of quick movements is sparks that fall of the

top of the workpiece. Move the plasma

burner at a

speed in which the spark

accumulation is concentrated on the bottom

side of the workpiece. Ensure the material is

completely separated prior to continuing with

this process. Set the necessary drag speed.

Using the device

327358_Plasmaschneider_PPS_40_B2_content_LB6_IE_NI.indb 18 06.09.2019 12:41:02

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PPS 40 B2 - IAN 327358 in the language / languages: English, German as an attachment in your email.

The manual is 2,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PPS 40 B2 - IAN 327358 Manual

Product: