763020

Parkside PPS 40 B2 - IAN 327358 Manual

17
Zoom out
Zoom in
Previous page
1/49
Next page
17GB/IE/NI
It must be operated in a dry and well
ventilated working environment.
• Connecting compressed air
PLEASE NOTE!
fThis device is designed for operating
pressure (output pressure at the com-
pressor) of up to 6.3 bar. Please bear in
mind that the pressure can lower while
setting the air pressure. Thus, in a hose
length measuring 10 m and an internal
diameter of 9 mm it drops by approx.
0.6 bar.
The compressed air source must have a filter
and regulator.
Connect the compressed air hose 16 on
the back of the plasma cutter 1 to the
compressed air connection 20. To do so,
insert the side of the compressed air hose
16 into the compressed air connection 20
of the plasma cutter 1 without a quick
connector (see Fig. I).
The pressure can be set via the knob 21
on the condensate separator (see
Fig. I-L). Select a pressure of 4–4.5 bar.
In order to release the compressed air
hose
16
, you must press the locking
mechanism of the compressed air connec-
tion
20
and pull out the compressed air
hose
16
at the same time (see Fig. I).
• Connecting the cutting torch
Insert the plasma burner plug 7 into the
plasma burner connection socket 12
and tighten the union nut hand-tight
(see Fig. A+B).
Insert the plasma burner power plug 6
into the plasma burner power socket 10
and tighten the union nut hand-tight
(see Fig. A+B).
• Connecting the ground cable
Connect the ground terminal plug 5 with
the ground terminal - connection socket 11.
Make sure that the connecting shaft is first
connected and then turned. The connecting
shaft must face upwards when plugging in
the ground cable plug 5. After plugging in,
the connecting shaft must be rotated in a
clockwise direction until it reaches the stop,
in order to lock it in place (see Fig. A+B).
This does not require force!
• Fitting the removable roller
guide (optional)
Push the removable roller guide 23 over the
nozzle clamping sleeve 8b, until the locking
screws 23a are completely above the black
area of the plasma burner 8 (behind the
gap at the back of the nozzle clamping
sleeve 8b) (see Fig. A+B). Now fix the
locking screws 23a . The guide rollers 23c are
now positioned such that the required
distance between the workpiece and burner
sleeve 8c is set. The roller guide is then fixed
in place 23 by tightening the fixing screws
23b (see Fig. N). Make sure that both guide
rollers 23c are always set to the same height,
in order to enable straight cutting. You can
see a correctly fitted roller guide in Fig. N.
Before use
327358_Plasmaschneider_PPS_40_B2_content_LB6_IE_NI.indb 17 06.09.2019 12:41:02
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PPS 40 B2 - IAN 327358 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PPS 40 B2 - IAN 327358 in the language / languages: English, German as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info