819505

Parkside PMRA 20-Li B2 - IAN 462730 Robot Manual

55
Zoom out
Zoom in
Previous page
1/388
Next page
GB MT
55
Working instructions
Regular mowing stimulates the grass to an
increased leaf formation, while at the same
time killing weeds. As a result, the lawn
becomes denser after each mowing and
an evenly resilient lawn is created.
The rst cut takes place roughly in April
when the grass is about 7 - 8 cm high. Dur-
ing the main growing season, the lawn is
mowed at least once a week.
Setting the cutting height
Switch off the device and wait for
the blades to come to a stop. There
is a risk of personal injury.
1. Open the cover (1).
2. Set the rotary wheel (2) to the desired
cutting height.
3. Close the cover (1) again.
The device can be adjusted in 15 steps to
a cutting height between 25 - 60 mm.
The correct cutting height is between 30
and 45 mm for an ornamental lawn and
about 30 to 65 mm for a utility lawn.
A high cutting height should be se-
lected for the rst cuts in the season.
Manually interrupting/
starting the operating cycle
Interrupting operation
Press the STOP button (9) to stop the mow-
er during operation.
Starting/resuming operation
1. Open the cover (1).
2. Conrm the selection with the OK but-
ton (7).
3. Unlock the display (10) with the 4-digit
PIN.
4. Press the start button (3).
5. Close the cover (1) again.
The lawn mower starts the set operat-
ing cycle or resumes its previous activi-
ty without interruption.
Operation
Setting the language
1. If necessary, open the cover (1).
2. Unlock the display (10) with the 4-digit
PIN.
3. Press the OK button (7) to enter the
main menu.
4. Use the arrow buttons (6) to select “Set-
tings” (Settings).
5. Conrm the selection with the OK but-
ton (7).
6. Use the arrow buttons (6) to select “Lan-
guage” (Language).
7. Conrm the selection with the OK but-
ton (7).
8. Use the arrow buttons (6) to select the
desired language.
9. Conrm the selection with the OK but-
ton (7).
10. Return to the main menu with the back
button (5).
Switching on and off
Switching on the lawn mower
(Fig. )
1. Press and hold the START button (3)
for approx. 3 seconds until the display
(10) lights up.
2. Enter the 4-digit PIN. You will nd
which buttons correspond to which
numbers in the section “Settings”.
3. Press the OK button (7) to enter the
main menu.
… 55 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PMRA 20-Li B2 - IAN 462730 Robot at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PMRA 20-Li B2 - IAN 462730 Robot in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info