819505

Parkside PMRA 20-Li B2 - IAN 462730 Robot Manual

51
Zoom out
Zoom in
Previous page
1/388
Next page
GB MT
51
8 m (314.96 inches) length
greater than or equal to 1.2 m
(47.24 inches)
The width of 1.2 m refers to the dis-
tance of the boundary wire. The
boundary wire is crossed by the lawn
mower 0.2 m on both sides when mowing.
Connecting the boundary
wire to the charging station
Illustration :
When laying the boundary wire
(11), leave it 0.5 - 1 m longer than
required to have wire left over for
corrections.
1. Strip approx. 10-15 mm of both ends
of the boundary wire (11) using cable
strippers.
2. Feed the cable end of the boundary
wire (11) arriving at the charging sta-
tion from behind through the groove
(28) under the charging station (17).
3. Clamp the wire end of the boundary
wire (11) that extends away from the
front and encloses the lawn area to be
mowed with the right-hand slot (luster
terminal with orange clamps pointing
upwards) of the luster terminal (11.1).
Clamp the cable end of the boundary
wire (11) that extends away to the rear
with the left slot (luster terminal with or-
ange clamps pointing upwards) of the
luster terminal (11.1).
4. Fold the cover (23) upwards.
5. Insert the luster terminal (11.1) into the
contact sockets (25/26) on the charg-
ing station (17).
6. Connect the mains plug (15) to the
power supply.
7. Check the LED (27) on the charging
station.
If the LED (27) lights up green, the
boundary wire (11) is connected to the
charging station (17) correctly.
Do not place the “protruding” re-
mains of the boundary wire togeth-
er. This can lead to faults and failures in
the lawn mower’s operation.
Fixing the charging station
The operating range indicator (30)
on the charging station must be lo-
cated within the restricted lawn area.
Illustration :
1. Loosen the mounting screws (12) and
the hexagon socket (12.1) from the
frame.
2. Place the charging station bumper (18)
on the side of the charging station with-
in the bounded lawn area.
3. Secure the charging station and charg-
ing station bumper (18) in the ground
with the mounting screw (12).
The mounting screws (12) are screwed
into the ground with the enclosed hex
key (12.1).
Initial start-up
Switching on the lawn mower
1. Press and hold the START button (3)
for approx. 3 seconds until the display
(10) lights up.
2. Set the desired language. Select with
the arrow buttons (6) and con rm the
selection with the OK button (7).
3. Set the date and time with the arrow
buttons (6).
Con rm the selection with the OK but-
ton (7). The individual positions can be
navigated with the OK button (7) (skip
the right).
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PMRA 20-Li B2 - IAN 462730 Robot at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PMRA 20-Li B2 - IAN 462730 Robot in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info