819505

Parkside PMRA 20-Li B2 - IAN 462730 Robot Manual

49
Zoom out
Zoom in
Previous page
1/388
Next page
GB MT
49
2. Press the charging unit (22) down so
that it is  rmly seated in the baseplate.
3. Fix the charging unit (22) from below
to the baseplate (21) with the four en-
closed screws (19).
Positioning the charging
station
Course for laying line of boundary
wire
160 cm (63 inches) minimum
distance
200 cm (78.74 inches) mini-
mum distance to wall
200 cm (78.74 inches)
minimum distance to next curve
100 cm (39.37 inches)
minimum distance to next curve
We recommend installing a roof for
the charging station (17) to protect
it from weather damage.
1. Choose a level position for the charg-
ing station (17) near a power outlet
with at least 2 m distance from the
boundary wire to the front and 1 m to
the rear.
Do not  x the charging station
until you have laid and connect-
ed the boundary wire. Please refer to
“Fixing the charging station” for this.
• The charging station may be inclined
max. 8 cm to the rear and max. 2 cm
to the front.
• Remove any unevenness under the
charging station. The charging station
must never sag.
• Make sure there is suf cient distance to
ponds, pools and steps.
Laying the boundary wire
Lay the boundary wire (11) around the
lawn area to be worked by the lawn mow-
er. You can do this as follows:
- Stake out the lawn area. Fasten the
boundary wire (11) with the hooks
(13) (above ground).
- Stake out the hooks at a maximum dis-
tance of 1 m. Use additional hooks if
the ground is uneven.
- Bury the boundary wire (11) in the
ground (max. 5cm deep).
The lawn mower crosses over the
boundary wire by about 20 -
30cm before it turns around and searches
for a new path. Install the boundary wire
accordingly to prevent damage.
For the initial installation, we recom-
mend marking out the boundary
wire (11) with the hooks (13) in case cor-
rections need to be made at a later date.
The mower works perfectly with a
boundary wire length of up to
200m. Do not use a longer boundary
wire.
• The lawn area must be bordered as a
single enclosed area.
Course for laying line of bound-
ary wire
• Any parallel boundary wires (11) in-
stalled at a distance of at least 10cm
are identi ed as an obstacle by the
lawn mower and are evaded.
equal to or greater than 10 cm
(3.94 inches)
• Any parallel boundary wires (11) at a
distance of 5mm or less are not detect-
ed by the lawn mower and are passed
over.
… 49 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PMRA 20-Li B2 - IAN 462730 Robot at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PMRA 20-Li B2 - IAN 462730 Robot in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info