679031
7
Zoom out
Zoom in
Previous page
1/14
Next page
Safety / Operation
9 GB/IE
J Always ensure that all the clamps and stops are
firmly held in place.
J Never saw through more than one workpiece at
a time.
J Ensure that the saw blade has reached full
speed before starting your cut and avoid using
too much force. In that way you will prevent the
saw blade from being blocked.
L Operation
L Assembly
Do not connect the chop and mitre saw to the mains
before you have worked through the following assembly
instructions and completely assembled the device.
1. Slide the lateral support stirrups
Y
into the
openings provided for them on the left and right
of the saw table
T
until they meet the stop and
then fully tighten the clamp screws
U
.
2. Screw the saw table setting knob
O
into the
threaded hole provided.
3. Loosen the saw table setting knob
O
again.
Press the mitre angle stop
I
and turn the saw
table
T
using the saw table setting knob
O
into
the basic position (0° setting).
4. When the mitre angle stop
I
has engaged in
the basic position (0° setting), turn the saw table
setting knob
O
to tighten it again.
5. Lightly press the switch handle
W
downwards
and pull out the transport lock
o
. The saw motor
unit
Q
tips upwards.
6. Ensure that the machine is standing in a stable
position and check that the floor around the
machine is flat, clean and free of loose particles
such as sawdust chippings and sawing waste.
Using the four mounting holes
}
provided, fasten
the chop and mitre saw on to a firm, level surface.
7. If you have not fastened the machine tightly
down to a working surface, pull out the rear
support stirrup
e
as far as possible to provide
maximum support to the machine.
L
Checking and setting your saw
Warning! Always disconnect the mains supply
(by pulling the plug out of the mains socket) before
you change any settings or check the condition of
the machine.
1. Parallel saw blade
j Check that the saw blade is correctly installed; it
must be parallel to the sawing slot in the table. To
make any necessary settings proceed as follows;
j Bring the saw table
T
into the basic position
(0° setting). Release the transport restraint by
lightly pressing the saw motor unit
Q
down-
wards and pulling out the transport lock
o
. Un-
lock the machine by pushing the safety lever
E
to the right. Lower the saw motor unit
Q
and
check that the side face of the saw blade is parallel
with the left hand edge of the sawing slot in the
table. The blade and the edge must be absolutely
parallel to one another. If necessary you can
change the setting by loosening the three
mounting screws
A
directly behind the saw
blade (see Fig. A) using the supplied 6 mm Allen
key (d) and bring the saw motor unit
Q
into
parallel alignment. Then retighten the mounting
screws.
2. Stop plate
j It is particularly necessary to check the stop
plate
q
if it has been removed from the machine
and put back again. The stop plate
must be
perpendicular (at 90°) to the saw blade. This
setting can only be made after the saw blade
has been set as described above. To check the
stop plate
q
, we recommend that you use a set
square. Set one end of the set square against
the stop plate and the other end against the side
face of the saw blade. If necessary you can
change the setting as follows:
j Loosen the two screws on the rear face of the
stop plate
q
using the supplied 6 mm Allen key
(d) and bring the stop plate
q
into a perpendi-
cular (90°) alignment to the side face of the saw
blade. Tighten the screws again.
7


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-pkgs-1450-laser---kh-3175

Reset search

  • Hallo, mijn naam is Bram Hexspoor en ben op zoek naar een tandwiel met schroef voor het bevestigen van het zaagblad.Bj. 2003
    Hij zit bevestigd aan de motor
    Het is een PARKSIDE TYP. PKGS 1450 afkortzaag met slive. Submitted on 12-12-2021 at 04:58

    Reply Report abuse
  • CAN I REPLACE THE LASER ON MY CHOP AND MITRE SAW IF SO WERE DO I GET ONE THANKS Submitted on 30-12-2020 at 14:45

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PKGS 1450 Laser - KH 3175 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKGS 1450 Laser - KH 3175 in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PKGS 1450 Laser - KH 3175

Parkside PKGS 1450 Laser - KH 3175 User Manual - German - 14 pages

Parkside PKGS 1450 Laser - KH 3175 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info