679031

Parkside PKGS 1450 Laser - KH 3175 Manual

8
Zoom out
Zoom in
Previous page
1/14
Next page
Operation
3. Saw blade depth
Wear protective gloves!
j Check the depth of the saw blade by first lowering
the saw motor unit
Q
as far down as possible.
Then try turning the saw blade manually. It must
be able to turn freely. If the saw blade does not
turn freely, carry out the necessary adjustment
by turning the setting screw
p
.
4a. Mitre setting 0°
j If necessary you can adjust the 0° mitre stop. Bring
the saw table
T
into the basic position (0°setting).
With the saw motor unit
Q
lowered, compare
the alignment of the side face of the saw blade
with the workpiece support surface of the table
using a set square.
To make the adjustment, first loosen the lock
nut on the setting screw
]
(see Fig. A) and then
turn the screw with the supplied 5 mm Allen key
(d). Take off the Allen key – readjust until the
saw blade is at 90° to the saw table. Tighten the
locknut on the setting screw
]
. The saw blade
must be at right angles to the saw table and the
scale on the saw motor unit
Q
must read 0°.
4b. Mitre setting 45° (inclined cut setting)
j Set the saw table
T
into the basic position
(0° setting). Loosen the setting knob
w
and
incline the saw motor unit
Q
until the 45°
setting on the scale
[
on the saw motor unit
is reached. Retighten the setting knob
q
and
lower the saw motor unit
Q
.
j Use a combination set square to check the angle
of the side face of the saw blade with respect to
the workpiece support area of the saw table. To
make the adjustment first loosen the lock nut on
the setting screw
S
(see Fig. B) and then turn
the screw with the supplied 5 mm Allen key (d).
Take off the Allen key – readjust until the saw
blade is at 45° to the saw table. Tighten the
locknut on the setting screw
S
.
5. Adjusting the pointer on the scale
[
If the pointer when it is in the basic setting is not in
line with the 0° marking on the scale then adjust the
pointer as follows:
j First make sure that the basic settings 0° and
45° have been carried out correctly as descri-
bed in sections 4a and 4b.
j Loosen the setting knob
w
and incline the saw
motor unit
Q
into the 45° setting.
j Loosen the pointer screw with a cross-head
screwdriver and adjust the pointer until it is in
line with the 45° marking and tighten the screw
again. After you have returned the saw motor
unit
Q
into the 0° position, the pointer should
again be exactly in line with the 0° marking on
the scale. If necessary repeat the adjustment
process until the pointer is correctly set.
L
Operation
Take note of the mains voltage! The voltage must agree
with that shown on the machine rating plate (equip-
ment shown as 230 V can also be connected to 220 V).
L
Connecting a dust extraction device
The dust created when sawing can be inflammable,
explosive and hazardous to health. Some dusts are
carcinogenic. Use a suitable dust extraction device
designed for the purpose and wear a dust protection
mask.
Wear a dust mask!
External vacuum extraction:
j Connect a vacuum extraction device of a type
specifically suitable for dust extraction to the
sawdust removal connector
r
. Ensure that you
connect and use it properly.
Sawdust collection bag (a):
j Attach the sawdust collection bag (a) to the sa-
wdust removal connector
r
by pressing the
lugs of the wire ring together. Engage the wire
ring in the groove provided in the sawdust re-
moval connector.
j To remove the sawdust collection bag (a) from
the sawdust removal connector
r
you also
press the lugs of the wire ring together.
10 GB/IE
… 8 …


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-pkgs-1450-laser---kh-3175

Reset search

  • Hallo, mijn naam is Bram Hexspoor en ben op zoek naar een tandwiel met schroef voor het bevestigen van het zaagblad.Bj. 2003
    Hij zit bevestigd aan de motor
    Het is een PARKSIDE TYP. PKGS 1450 afkortzaag met slive. Submitted on 12-12-2021 at 04:58

    Reply Report abuse

  • CAN I REPLACE THE LASER ON MY CHOP AND MITRE SAW IF SO WERE DO I GET ONE THANKS Submitted on 30-12-2020 at 14:45

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PKGS 1450 Laser - KH 3175 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKGS 1450 Laser - KH 3175 in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PKGS 1450 Laser - KH 3175

Parkside PKGS 1450 Laser - KH 3175 User Manual - German - 14 pages

Parkside PKGS 1450 Laser - KH 3175 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info