679031

Parkside PKGS 1450 Laser - KH 3175 Manual

9
Zoom out
Zoom in
Previous page
1/14
Next page
Empty the sawdust collection bag regularly.
Open the zip fastener to empty the bag.
L
Unlocking and switching
the machine on and off
j Unlock the machine by pushing the safety lever
E
to the right.
Switching on:
j Press the On / Off switch
D
and keep it pressed.
Note: There is a delay in the machine starting up
.
Switching off:
j Release the On / Off switch
D
.
j Secure the machine again by moving the saw
motor unit
Q
downwards and pressing the
transport lock
o
to the left.
L
Switching the laser on and off
and adjusting it
Avoiding harm from the laser beam!
The laser beam indicates the cutting line of the saw
blade. Align the marks on your workpiece with the
track of the laser beam.
Switching on:
j Press the laser On / Off switch
i
into position I.
Switching off:
j Press the laser On / Off switch
i
into position 0.
Adjusting the laser beam:
j Turn the laser setting screw
H
to adjust the
laser beam.
L
Setting the speed
You can pre-select the speed you require using
the rotation speed selector wheel
F
.
Increasing speed:
j Turn the rotation speed selector wheel
F
towards marking 6 or in the + direction
(6= highest speed).
Reducing speed:
j Turn the rotation speed selector wheel
F
towards marking 1 or in the – direction
(1= lowest speed).
L
Transporting the machine
j Before you transport the machine always lock
the transport restraint by engaging the transport
lock
o
with the saw motor unit
Q
lowered.
When you carry the machine always hold it by
the base.
L
Attaching the laminate cutting
attachment and cutting laminate
The patented laminate cutting attachment
{
allows
you to cut laminate to your required lengths quickly
and cleanly. Note that the laminate cutting attach-
ment
{
is designed exclusively for laminate and
a material width of up to 20 cm. It is suitable for
almost all types of commercially available laminate
floor coverings.
j Loosen the two stop plate
q
setting screws
using the supplied 6 mm Allen key (d) and re-
move the stop plate.
j Insert in its place the laminate cutting attach-
ment
{
and screw it to the saw table
T
.
j Place the laminate flush against the edge of
the stop of the laminate cutting attachment
{
.
L
Mitre cuts – turning the saw table
j Loosen the setting knob for saw table
O
. Press
the mitre angle stop
I
and turn the saw table
T
using the saw table setting knob
O
to the left or
right into the desired position. Release the mitre
angle stop
I
again and tighten the saw table
setting knob
O
.
Operation
11 GB/IE
… 9 …


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-pkgs-1450-laser---kh-3175

Reset search

  • Hallo, mijn naam is Bram Hexspoor en ben op zoek naar een tandwiel met schroef voor het bevestigen van het zaagblad.Bj. 2003
    Hij zit bevestigd aan de motor
    Het is een PARKSIDE TYP. PKGS 1450 afkortzaag met slive. Submitted on 12-12-2021 at 04:58

    Reply Report abuse

  • CAN I REPLACE THE LASER ON MY CHOP AND MITRE SAW IF SO WERE DO I GET ONE THANKS Submitted on 30-12-2020 at 14:45

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PKGS 1450 Laser - KH 3175 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKGS 1450 Laser - KH 3175 in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PKGS 1450 Laser - KH 3175

Parkside PKGS 1450 Laser - KH 3175 User Manual - German - 14 pages

Parkside PKGS 1450 Laser - KH 3175 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info