Manual Parkside PKGS 1450 Laser - KH 3175 (page 6 of 14) (English)

679031

6

Zoom out

Zoom in

Previous page

1/14

Next page

Safety

J Do not operate the device if it is

damp and do not use it in a damp

environment.

Protecting yourself from laser radiation:

Note: This product is a Class 1 Laser / Protection

Class III device. The radiation output under circum-

stances of proper use does not present any danger.

J The chop and mitre saw is ﬁtted with a laser.

Do not replace this laser with one of another

type. Repairs must be carried out only by one

of our authorised service partners.

J Do not look directly into the laser beam or into

the opening from which it is emitted.

J Never direct the laser beam on to reﬂective sur-

faces or at people or animals. Even a brief look

into a laser beam can damage your eyes.

J Never open the laser unit housing.

To avoid the danger of injury,

burning and dangers to your health:

J Always check the device ﬁrst under no-load

conditions. If you notice any strange noises or

vibrations from the device, switch it off immedi-

ately and pull the plug out of the mains socket.

Never use the device if it shows any of these

types of problems. Take it to be checked and if

necessarily repaired by an electrician.

J Use the machine only on the materials given in

the section on proper use.

J Check that the saw motor unit

Q

is securely

attached.

J Use the machine only if the safety equipment is

properly positioned in its place as intended, the

machine is in good condition and has been

properly maintained.

J Always keep the mains lead away from the

working area of the machine and lead away the

mains lead from the rear.

J

Look after your health – wear

ear protectors, safety glasses

and a breathing / dust mask.

J Never hold the saw at the rear. Remove sawing

waste, parts of workpieces or clamped objects

only when the machine’s mains plug is removed

from the mains socket and the saw has come to

a standstill.

J Do not cut workpieces too small. Your hand must

always be at least 10 cm away from the saw blade.

J Do not attempt to saw extremely small work-

pieces.

J

Ensure that your work area is well lit

(250 - 300 Lux).

Do not use the device in places

where there is a danger of ﬁre or explosion, for

example near inﬂammable liquids or gases.

J If the table insert

G

is damaged have it replaced

immediately.

Danger! If the table insert is damaged it could

lead to the danger of small objects blocking the

saw blade by becoming trapped between the

table insert

G

and the saw blade. If the table

insert is damaged have it replaced immediately

by our customer service department.



To work safely:

J Use the machine only for the purposes indicated

and within the stipulated performance limits.

Do not overload the machine.

J Keep the handle clean, dry and free of oil and

grease.

J Ensure that the automatic blade guard

R

is

functioning properly and can move freely. Never

clamp the automatic blade guard so that it re-

mains open.

J Always select a saw blade that is suitable for

the material you intend to cut.

J Support longer workpieces in such a way that

they are at the same level as the surface of the

saw table

T

.

J Secure the machine after use with the transport

lock

o

.

J Use the screw clamps (b) or other clamping

devices so that an awkwardly shaped workpiece

cannot rotate or move whilst you are sawing it. The

workpiece must be ﬁrmly clamped against the

base of the table and the stop plate so that there

are no gaps between the turntable and workpiece

or between the stop plate and the workpiece.

8 GB/IE

1

Hallo, mijn naam is Bram Hexspoor en ben op zoek naar een tandwiel met schroef voor het bevestigen van het zaagblad.Bj. 2003
Hij zit bevestigd aan de motor
Het is een PARKSIDE TYP. PKGS 1450 afkortzaag met slive. Submitted on 12-12-2021 at 04:58
Reply Report abuse
CAN I REPLACE THE LASER ON MY CHOP AND MITRE SAW IF SO WERE DO I GET ONE THANKS Submitted on 30-12-2020 at 14:45
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Parkside PKGS 1450 Laser - KH 3175 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKGS 1450 Laser - KH 3175 in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PKGS 1450 Laser - KH 3175

Parkside PKGS 1450 Laser - KH 3175 User Manual - German - 14 pages

Parkside PKGS 1450 Laser - KH 3175 User Manual - Dutch - 14 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info