746858

Parkside IAN 292193 PDTS 6.3 A1 Manual

31
Zoom out
Zoom in
Previous page
1/117
Next page
GB/IE/NI 31
Warnings specific to the pneumatic angle grinder / Operation
Otherwise, accessories turning
faster than permitted may be
damaged irreparably.
Make sure that the parting disc
size is appropriate for the pneu-
matic angle grinder and that the
parting disc fits on the spindle.
Parting discs must be stored and
handled with care and in accord-
ance with the manufacturer’s
instructions.
Inspect the parting disc before
use, and discard all that have
spalled, fractured, or sustained
any other damage.
Before use, make sure that the
parting disc has been fitted cor-
rectly and tightened securely, and
let the device run idle for thirty
seconds in a safe place. Stop the
machine immediately there are
considerable vibrations or defects.
If this is the case, examine the
devices and identify the cause.
Do not use separate adapters or
adapter bushes: use instead
parting discs with a larger hole
diameter.
Always use the recommended
guard supplied with the pneumatic
angle grinder. The opening in the
guard must face away from the
operator.
Do not use angle grinders for
face cutting.
The parting disc continues
rotating even after the device has
been switched OFF. After switch-
ing OFF, the device may not be
put down until the parting disc
has come to a complete stop. This
precautionary measure serves to
prevent not only serious accidents,
but also dust and chips from being
sucked into the devices.
Operation
Before starting up
Fit the parting disc
Disconnect the compressed air supply from the
compressed air connection.
Use the assembly key
7
to lock the spindle in
place, at the same time loosening the hex screw
and flange with the Allen key
8
.
Fit the new parting disc
6
and flange on the spin-
dle. Use the Allen key
8
to tighten firmly the Allen
screws. Check that the parting disc has been fitted
correctly and can rotate without hindrance!
Protective cowl
Flange
75 mm parting disc
Hex screw
Spindle
Trigger arm
Switch ON guard
Compressed air connection
Compressed air supply and connection. Use
filtered, lubricated, and regulated compressed air
only. The following figure illustrates the correct way
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 292193 PDTS 6.3 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 292193 PDTS 6.3 A1 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info