746858
32
Zoom out
Zoom in
Previous page
1/117
Next page
GB/IE/NI32
Operation
of connecting to the compressed air system, and
tool effectiveness and life is extended as a result.
Connecting sleeve
Compressed air hose
Quick release connector Compressor
Pressure regulator
Oiler Filter
Quick release connector
Quick release connector
Before first use and thereafter at regular intervals,
apply a few drops of pneumatic equipment or
motor oil SAE 10-20 into the compressed air
connection on the pneumatic device. After every
3–4 operating hours, use the assembly key to
remove the screw plug
9
in the oil reservoir.
Fill the oil reservoir with pneumatic equipment or
motor oil SAE 10-20, and insert the screw plug
back. Wrap some Teflon sealing tape around the
thread on the air connections. Screw the air con-
nections into the pneumatic devices.
Starting up
Put on protective clothing and goggles.
OTHERWISE THERE IS DANGER OF INJURY!
Check that the parting disc has been tightened
securely.
Check that the workpiece is supported or has been
locked in place correctly. A C clamp is recom-
mended on loose workpieces.
Make sure that generated sparks do not pose any
danger, i.e. they cannot contact any persons or
ignite flammable substances.
Connect the compressed air supply. To do so, con-
nect the compressed air source to the compressed
air connection.
Press the switch ON guard towards the chuck.
Press the trigger arm, and perform the cutting work.
The device rotates at the maximum speed when the
trigger arm is tightened to the stop. Regulate the
tightening pressure and therefore the speed for the
optimal grinding results.
Switching OFF
Release the trigger arm
2
to switch OFF the
pneumatic angle grinder.
After work, disconnect the device from the
compressed air source.
Note: First detach the hose from the compressed
air source, and then remove the supply hose from
the device. This prevents the supply hose from
whirling out of control.
Maintenance
If the machine is to enjoy a long service life and
operate without problems, it is important that the
following maintenance instructions are followed.
The pneumatic angle grinder must be lubricated
regularly if it is to operate flawlessly at all times.
ATTENTION: DISCONNECT COMPRESSED AIR
BEFORE MAINTENANCE WORK!
Keep the pneumatic devices clean.
Turn over the tool so that the compressed air con-
nection points upwards, and apply a few drops of
pneumatic equipment or motor oil SAE 10-20 into
the compressed air connection on the pneumatic
devices.
Press the trigger arm
7
to distribute the oil more
evenly. Hold a cloth or absorbent paper towel in
front of the exhaust air openings, and let the device
run in idle mode for a few seconds.
ATTENTION! EXCESS OIL IS BLOWN OUT. KEEP
THE DISCHARGE HOLE AWAY FROM PERSONS
AND OBJECTS.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 292193 PDTS 6.3 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 292193 PDTS 6.3 A1 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info