745555
48
Zoom out
Zoom in
Previous page
1/204
Next page
48
GB IE
- On the guide rail for the parallel stop
(13) there are 2 scales (j/k). These
show the distance between the stop
rail (39) and saw blade (5) (Figure
27).
- Select the suitable scale according to
whether the stop rail (39) has been
turned around for working with thick
or thin material:
High stop rail (thick material):
scale (j)
Low stop rail (thin material):
scale (k)
- Adjust the parallel stop (14) to the
desired level on the sight glass (l) and

Adjusting the Stop Length
(Figure 29)
- In order to prevent the material being
cut from jamming, the stop rail (39)
can be moved in the longitudinal
direction.
- Rule of thumb: the rear end of the
stop abuts on an imaginary line. This
begins at about the middle of the saw
blade and runs towards the back at an
angle of 45°.
- Adjust the required cutting width.
- Release the wing nuts (h) and push
the stop rail (39) forwards until the
imaginary 45° line is touched.
- Retighten the wing nuts (h).
Adjusting the Parallel Stop
(Figure 30)
- Caution! Remove the guard.
- Adjust the saw blade (5) to the maxi-
mum cutting depth.
- Adjust the parallel stop (14) such that
the stop rail (39) touches the saw
blade (adjustment for thick material.
- If the parallel stop (14) is not parallel
to the saw blade (5), please proceed
as follows. Release the screws (m) on
the parallel stop until the parallel stop
(14) can be aligned to be parallel with
the saw blade (5) (Figure 30).
- Retighten the screws (m).
Transverse stop
(Figure 31)
- Push the transverse stop (8) into a
groove (32) of the saw table.
- Loosen the knurled screw (33).
- Turn the transverse stop (8) until the
desired angle is set. The notch on the
guide bar shows the angle that has
been set.
- Retighten the knurled screw (33).
- When the wood is being cut to
size, the transverse stop (8) must be
extended with the stop rail (39) of the
parallel stop (14) (Figure 31)
- In order to extend the transverse stop
(8) with the stop rail (39), the stop
rail (39) has to be removed from the
parallel stop (14). Now the stop rail
has to be mounted as shown in Figure
31; use the star grips (q) for this.
Caution!
- Do not push the stop rail (39) too far
in the direction of the saw blade.
- The distance between the stop rail (39)
and saw blade (5) should be approxi-
mately 2 cm. (Figure 31).
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 273460 PTK 2000 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273460 PTK 2000 B2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info