Manual Parkside IAN 273460 PTK 2000 B2 (page 49 of 204) (English, German, Dutch, French, Italian, Portuguese, Spanish)

745555

Zoom out

Zoom in

1/204

GB IE

- Switch on the laser: turn the laser on/

off switch (35) to I. When the saw bla-

de guard (2) is mounted, the laser on/

off switch (35) is accessible through a

recess in the guard (Figure 33). A red

laser beam is now projected out of the

laser exit aperture. If you guide the

laser beam along the cutting line mark

while sawing, you will achieve clean

cuts.

- Switch the laser off: turn the laser on/

off switch (35) to 0. The laser beam

goes off. Please always turn the laser

off when it is not required in order to

save the batteries.

- The laser beam may be blocked by

dust deposits and chips. You should

therefore remove these particles from

the laser exit aperture after every use

(with the device switched off).

Adjusting the Laser

(Figure 34)

If the laser (34) no longer shows the

correct cutting line, this can be readjusted.

To do this, open the screws (z). Adjust the

laser with the help of the adjusting screw

(y) such that the laser beam impinges on

the cutting teeth of the saw blade (5).

Operation

Working Instructions

After each new adjustment, we recommend

a trial cut in order to check the set dimen-

sions. After the saw has been switched on,

wait until the saw blade has reached its

maximum speed before you carry out the

cut.

Secure long workpieces against tilting at

the end of the cutting process (e.g. unwin-

ding stand etc.)

Adjusting the Scale of the

Transverse Stop

(Figure 32)

- Create a 90° stop angle with respect

to the saw blade (5).

- Connect the transverse stop (8) to the

stop rail (39) of the parallel stop 14)

(see also Transverse Stop).

- Loosen the knurled screw (33) of the

transverse stop (8).

- Position the transverse stop (13) such

that the stop rail is at an angle of 90°

to the saw blade (5). Now align the

transverse stop precisely with the help

of the 90° angle to the saw blade and

retighten the knurled screw (33).

- Check whether the transverse stop

shows exactly 90°. If this is not the

case, please proceed as follows:

- Release the two screws (o) with which

the scale (p) of the transverse stop (8)

is attached to it. Now the scale can be

adjusted to the correct position.

- Now retighten the screws (o) (see



Using the Laser

(Figures 33-34)

- The laser (34) enables you to carry out

precision cuts with your circular saw.

- The laser light is produced by a laser

diode supplied by two batteries. The

laser light is expanded to form a line

and is emitted through the laser exit

aperture. You can then use the line as

an optical marking for the cutting line

of the precision cut. Please note the

laser safety information.

- Insert the batteries

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273460 PTK 2000 B2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 273460 PTK 2000 B2 Manual

Product: