745555

Parkside IAN 273460 PTK 2000 B2 Manual

47
Zoom out
Zoom in
Previous page
1/204
Next page
47
GB IE
Working with the Parallel
Stop
Adjusting the
Stop Height
(Figures 24-26)
- The stop rail (39) of the parallel stop
(14) has two guide surfaces at diffe-
rent heights.
- Depending on the thickness of the ma-
terials to be cut, the stop rail (39) has
to be used differently. For thin material
(workpiece thickness less than 25
mm), use Figure 24. For thick material
(workpiece thickness more than 25
mm), use Figure 26.
Turning the Stop Rail
(Figures 24-26)
 
of all release the two wing nuts (h).
- Now the stop rail (39) can be pulled
off the guide rail (14) and pushed
back over this again with the correct
guide mechanism.
- Retighten the wing nuts (h).
Adjusting the Cutting
Width
(Figures 27-28)
- When wooden pieces are being cut
lengthwise, the parallel stop (14) has
to be used.
- The parallel stop should be mounted
on the right-hand side of the saw
blade (5).
- Insert the parallel stop into the side of
the guide rail (13) (Figure 28).
- In order to switch the saw off again,
the red pushbutton „0“ has to be
pressed.
Adjusting the Cutting
Depth
(Figure 23)
By turning the hand wheel (12) to adjust
the height, the saw blade can be set to the
desired cutting depth (continuous).
Important: the hand wheel (12) has
to be pulled out to adjust the cut-
ting depth. When the hand wheel is
pressed in, this adjusts the cutting
angle.
- Anticlockwise: increases the cutting
depth
- Clockwise: reduces the cutting depth
Check the adjustment by means of a
test cut.
Angle Adjustment
(Figure 23)
With the table circular saw it is possible to
make bevel cuts to the left at an angle of
0° to 45° to the stop rail. Before each cut,
make sure that no collision is possible bet-
ween the stop rail (39), cross-cutting gauge
(Figure 1, no. 8) and the saw blade (5).
- Release the locking handle (9)
- Set the desired angle on the scale
by pressing in and turning the hand
wheel (12).
- Lock the locking handle (9) in the
desired angular position.
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 273460 PTK 2000 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273460 PTK 2000 B2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info