Manual Parkside IAN 273460 PTK 2000 B2 (page 50 of 204) (English, German, Dutch, French, Italian, Portuguese, Spanish)

745555

Zoom out

Zoom in

1/204

GB IE

Caution with incision cutting.

Operate the device only with a suction sys-

tem. Check and clean the suction channels

regularly.

Suitability of the saw blades:

- 24 teeth: soft materials, high chip

removal, rough cut image

- 48 teeth: hard materials, lower chip



Performing Longitudinal

Cuts

(Figure 35)

Here, a workpiece is cut in its longitudinal

direction. One edge of the workpiece

is pressed against the parallel stop (14)



The saw blade guard (2) must always be

lowered onto the workpiece. The working

position during longitudinal cutting must

never be in a straight line with the cutting

line.

- Adjust the parallel stop (14) according

to the workpiece height and the desi-

red width.

- Switch on the saw.

 



and push the workpiece along the

parallel stop (14) into the saw blade

(5).

- Guide from the side with your left or

right hand (depending on the position

of the parallel stop) only up to the front

edge of the saw blade guard (2).

- Always push the workpiece through to

the end of the riving knife (4).

- The cutting waste remains on the saw

table (1) until the saw blade (5) is

back in its resting position.

- Secure long workpieces against tilting

at the end of the cutting process! (e.g.

unwinding stand etc.)

Cutting narrow

Workpieces

(Figure 36)

Longitudinal cuts of workpieces with a

width of less than 120 mm always have to

be cut with the help of a push stick (17).

The push stick is included in the scope of

delivery. Replace a worn or damaged

push immediately.

• Adjust the parallel stop according to

the planned workpiece width.

• Advance the workpiece with both

hands, making sure that you use a

push stick (17) as a pushing aid in the

vicinity of the saw blade.

• Always push the workpiece through to

the end of the riving knife.

Caution! In the case of short work-

pieces, the push stick should be

used from the beginning of the

cutting process.

Cutting very narrow

Workpieces

(Figure 37)

For longitudinal cuts of very narrow work-

pieces with a width of 30 mm and less, a

push block must be used without fail. There

is no push block included in the scope of

delivery! (Available from specialist shops)

Replace a worn push block as soon as

possible.

• The parallel stop should be adjusted to

the cutting width of the workpiece.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273460 PTK 2000 B2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 273460 PTK 2000 B2 Manual

Product: