745555
43
Zoom out
Zoom in
Previous page
1/204
Next page
43
GB IE
Alternating Current Motor
The mains voltage must be 230 V~.
Extension cables up to 25 m in length
must have a cross-section of 2.5 mm².
Connections and repairs to the electrical
equipment may only be performed by

queries, please provide the following
information:
Current type of the engine
Data from the machine type plate
Data from the motor type plate
Assembly
Assembly, Replacement of Parts
and Adjustments
Caution! The mains plug must be
removed before all servicing, ret-
ooling and assembly work.

surface. Form groups of the parts which
are similar.
Note: If connections are secured with a
bolt (round head/or hexagonal), hexago-
nal nuts and a washer, the washer must be
placed under the nut.
Insert the bolts from the outside to the in-
side in each case, securing the connections
with nuts from the inside.
Note: Tighten the nuts and bolts during as-
sembly only to the extent that they cannot
fall off.
If you tighten the nuts and bolts any further


Additional tool required:
- Phillips screwdriver
Mounting of the Frame
Abb.4-10
1. Turn the table circular saw over and

2. Unscrew the four mounted rubber feet
with a Phillips screwdriver (Figure 5).
3. Screw the four legs (18) with the
hexagon bolts (e) loosely on to the
saw (Figure 6). Use the jaw spanner
(r) supplied for this.
Caution! 2 of the legs have
holes (38) drilled into the rear,
into which the stand brackets

and 10) Ensure that these are
attached at the rear of the ma-
chine.
4. Now take the cross struts (19) (marked
A) and longitudinal struts (20) (marked
B). Screw these loosely together with
the four central struts (21, 22) to the
legs. Mounting material: Round head
bolts (d), washer (a), spring washer (b)
and nuts (c), (Figure 6-8).
5. The round head bolts (d) and nuts (c)
should only be loosely tightened.
Caution: The longer struts
(marked B) must be used at the
side. Secure the central struts

shown in detail in Figure 8.
6. Now attach the rubber feet (23) to the
legs (Figure 9).
7. Screw the stand brackets (24) into the
rear legs using the drill holes. Moun-
ting material: 2 each: round head
bolts (d), shims (a), spring washer (b)
and nuts (c), (Figure 10).
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 273460 PTK 2000 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273460 PTK 2000 B2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info