668497
36
Zoom out
Zoom in
Previous page
1/51
Next page
36
12.2 Errors shown by the sensor control board
If the fault is related to the levelling, the Main board will show E97 or E98, which means that you
have the check the error at the sensor control board.
12.2.1 Diagnostic displays
The display at the sensor control board shows the actual error. More detail and updated info of these
display errors is attached to this document.
The display can show the following errors.
‘ ‘ System 2 in sleepmode, “no power” on Sensor control PCB. (nothing visible in display)
1 Complete system ready to run. (System 1 + 2 ready to start / no E-erros on both systems)
MAIN BOARD RELATED FAULTS
E25 No response main drive. (via CAN)
E26 Fail Safetyline test Main drive
E27 Fail Selftest Main drive.
LEVEL BOARD RELATED FAULTS
E30 No response level drive. (via CAN)
E31 Fail Safetyline test Level drive
E32 Fail Selftest Level drive.
E33 Overload Level motor
E34 Supply voltage (remark level should be lower/higher than Main PCB)
E35 Locked rotor / encoder fault Level motor
E36 Motor direction error
E37 Gate supply voltage missing, SLA and/or SLB not active (Tilt sensor?)
E38 Overcurrent , encoder fault Level motor
SENSORCONTROL BOARD FAULTS
E40 General PCB fault
E41 FAIL Test ADC lift sensor
E42 FAIL test voltage lift sensor (gyro)
E43 Max Omega lift sensor during movement
E44 Checksum error
E45 Sensors not calibrated.
CHAIRSENSORS FAULTS
E50 Chair sensor measures system is more then 3,5 degrees out of level.
E51 FAIL test ADC Chair sensor
E52 FAIL test voltage Chair sensor (gyro)
E53 FAIL test voltage Chair sensor (Vx/y)
E54 Max Omega Chair sensor during movement
SAFETYLINE / TILTSENSOR FAULT
E60 Safety line A (SLA) and B (SLB) not intact. (Tilt sensor ?)
E61 Safety line A (SLA) not intact.
E62 Safety line B (SLB) not intact.
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Otolift One at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Otolift One in the language / languages: English as an attachment in your email.

The manual is 4,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info