668497

Otolift One Manual

37
Zoom out
Zoom in
Previous page
1/51
Next page
37
12.1.2 Error-log
The PCB stores the errors in its memory.
By using the 2 buttons at this PCB, you can read out the error-log.
Facts & functions of error-log
- Control lower switch => read the stored errors backwards
- Control upper switch => start at latest stored error
- Control upper switch for 10 sec. => delete error-log
- Errors are only stored when the lift is controlled by armrest left/right or remote up/down.
- Maximum of 20 errors can be stored.
- The end of the error-log is shown as a minus
Example.
If you had a problem and you read back the errorlog you could read for example;
E38, E38, E45, -
The E38 shows that somehow the level motor shows overload problems.
The E45 shows that the system needed calibration of all sensors.
( it is normal, when you have a new system, the lift had generated a E45 fault, see chapter 5.4)
When you read back the errorlog of the main drive you could read.
2, 2, _ , E97, E97,_ , _ , _ 2, 2, E98, -
The error 2 points at a possible failure at the swivel seat switch.
The underscore shows that the lift did show any problems for some days.
The Error E97 means that the main board received a fault form the sensor control board and that the
main board does not have to generate the technician needed beep.
The Error E98 means that the main board received a fault form the sensor control board and that the
main board needs to generate the technician needed beep.
Combined log
You can combine both logs in 1 log, cause the E97 and E98 error are set by the errors measured by the
sensor control board.
Main board log 2, 2, _ , E97, E97,_ , _ , _ 2, 2, E98, -
Sensor control board log E38, E38, E45, -
=================================================== +
Combined log 2, 2, _ , E38, E38,_ , _ , _ 2, 2, E45, -
Again the error 2 points at a possible failure at the swivel seat switch.
The underscore shows that the lift did show any problems for some days.
The E38 shows that somehow the level motor shows overload problems.
The E45 shows that the system needed calibration of all sensors.
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Otolift One at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Otolift One in the language / languages: English as an attachment in your email.

The manual is 4,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info