16646
22
Zoom out
Zoom in
Previous page
1/65
Next page
15
ENGLISH
NOTE: Program all the desired features at the same time in order to
create a single receipt of all selections. Keep the receipt in a safe
place for future reference.
Making Changes to Cash Register Programming
Once the cash register is programmed to satisfy your specific needs,
there is no need to reprogram the entire machine to make single program
changes or corrections. If you wish to make a change (such as an update
to VAT rates, PLUs or Euro exchange rates), be sure you are in the
program mode, re-do the program in question and finalize when you are
ready to exit the programming mode. A new program entry will
automatically overwrite a previous entry for the same program.
Entering the Program Mode
To enter into the program mode, unlock, open and remove the printer
compartment cover and then slide the control switch to the PRG position.
Refit the printer compartment cover.
Exiting the Program Mode
To exit the program mode, open the printer compartment cover and slide
the control switch to the R1 or R2 position if you wish to carry out sales
transactions, to the X or Z position if you wish to take management
reports, or to the OFF position if you wish to exit.
Clearing Errors
To clear an error made during the programming phase, simply press the
[C] key. The error tone ends, the display clears and the keypad unlocks.
If the message "SEC Code" is displayed, this means that a PRG and Z
mode security password was programmed. Enter the 4-digit code followed
by the [Charge] key to continue.
In case an error condition cannot be cleared, perform one of the two
general clearance methods explained in the section entitled General
Clearance. Remember that the second general clearance sets all
counters and totals to zero, and cancels all features programmed.
Clerk Numbers and Secret Codes
Clerk codes are a special security feature to control access to the
register. You can program up to 6 individual clerk numbers linked to secret
entry codes of three digits each.
Programming a Secret Code Linked to a Clerk
Number
1. Open the printer compartment and slide the control switch to the PRG
position.
2. Activate the clerk system by typing [44444] followed by [1] and then
pressing the [Amt Tend/TOTAL] key.
3. Type [444444] and press the [Amt Tend/TOTAL] key.
4. Type a number to identify the clerk which the secret code will be
linked.
5. Set a three-digit secret code by typing three [numeric keys].
6. Press the [Clerk] key.
Repeat the above operations (from step 3 to step 6) to assign a secret
code to the remaining 5 Clerks or use the [C] key to exit from Clerk
Secret Code programming.
If you wish to change the clerk's secret code and the Clerk system is
already activated, there is no need to perform step 2 above.
Example: Assign secret code 106 to Clerk 1 for the first time.
Type/Press:
[44444] + [1] + [Amt Tend/TOTAL] + [444444] + [Amt Tend/TOTAL] +
[1106] + [Clerk]
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olivetti ECR5200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olivetti ECR5200 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Olivetti ECR5200

Olivetti ECR5200 User Manual - German - 72 pages

Olivetti ECR5200 User Manual - French - 70 pages

Olivetti ECR5200 User Manual - Spanish - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info