This appliance is equipped with a temperature sensor and automatic shutdown system to protect the induction hob from damage. The temperature
inside the induction hob is continuously monitored and the appliance will switch o automatically when a critical temperature is being measured.
Detection of small articles
When a cooking zone is switched on and a pot of unsuitable size, a non-magnetic pot (e.g. aluminium), or a small item (e.g. knife, fork, key) is detected on
the appliance, it automatically enters standby-mode after 1 minute. The fan will keep cooling down the appliance for a further 1 minute.
Automatic shutdown functions
•Shutdown function A: Cooking zones with a suitable pot still on it will be shut down after a certain amount of time has elapsed. The time until
shutdown depends on the heat level setting:
Power levelKeep warm123456789
Default working timer28 hours4 hours2 hours
•Shutdown function B: When the pot is removed from the cooking zone but you forget to switch o the cooking zone the appliance stops heating
immediately. The hob automatically switches o after 2 minutes.
TROUBLESHOOTING
Problem / Error code displayPossible CauseSolution
The cooktop cannot be turned on.No power.Make sure the cooktop is connected to the power
supply and that it is switched on.
Check the household fuse for the appliance. Check
whether there is a power cut by trying other electric
appliances.
The touch controls are unresponsive.The controls are locked.Unlock the controls (Child lock).
The touch controls are dicult to
operate.
There may be a slight lm of water over the controls or
you may be using the tip of your nger when touching
the controls.
Make sure the touch control area is dry. Use the ball of
your nger when touching the controls.
Some pans make crackling or
clicking noises.
This may be caused by the construction of your
cookware (layers of dierent metals vibrating
dierently).
This is normal for cookware and does not indicate a
fault.
The induction hob makes a low
humming noise when used on a
high heat setting.
This is caused by the technology of induction cooking.This is normal, but the noise should quieten down or
disappear completely when you decrease the heat
setting.
Fan noise coming from the
induction hob.
A cooling fan built into your induction hob has come
on to prevent the electronics from overheating. It may
continue to run even after you’ve turned the induction
hob o.
This is normal and needs no action. Do not switch the
power to the induction hob o at the wall while the
fan is running.
Pan does not heat up and it does not
appear in the display.
The induction hob cannot detect the pan because it is
not suitable for induction cooking.
Use cookware suitable for induction cooking
( Choosing the right cookware).
The induction hob cannot detect the pan because it is
too small for the cooking zone or not properly centred
on it.
Centre the pan and make sure that its base matches
the size of the cooking zone.
Error code
.
Temperature sensor failure or other issue.Contact your retailer or a qualied technician.
Error code
.
Abnormal supply voltage.Inspect whether power supply is normal.
Power on after the power supply is normal.
Error code .
Abnormal temperature.Inspect the pot in use.
The hotplate has overheated and has switched o in
order to protect the hob.
Wait until the electronic system has cooled suciently.
Then, switch on again.
CARE AND MAINTENANCE
Warning!
Always switch o the electricity supply before performing maintenance work. In the event of a fault, contact an ocial distributor or authorised dealer.
•If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
•For domestic use only.
•Never place the induction hob directly into water.
•Never place an empty pan on the hob as this might cause damage to the pan. The over-temperature protection might cause an automatic shutdown
of the appliance.
•When a cooking zone has been on for a long time, the surface remains hot for some time afterwards so do not touch the glass surface.
•Occasionally check that nothing is obstructing the air inlet beneath the induction hob.
•If the surface of the hob is cracked, disconnect from power supply the appliance to avoid any possibility of electric shocks.
•Do not place rough or uneven vessels on the hob, as they could damage the glass surface.
•Avoid banging pots and pans down on the hob.
The glass surface is tough but not unbreakable.
•Do not leave metal objects, such as knives, forks, spoons and lids on the hob as they may get hot.
•Do not store detergents or ammable materials beneath the hob.
•Only clean the hob when it has cooled suciently.
•When the power to the cooktop is switched o, there will be no residual heat indication but the cooking zone may still be hot. Take extreme care!
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for OK OBH39831 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of OK OBH39831 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish as an attachment in your email.
The manual is 10,47 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
