568780

OK OBH39831 Manual

28
Zoom out
Zoom in
Previous page
1/110
Next page
28
EN
Electrical connection and alterations
Caution!
• Check with an electrician whether the domestic wiring system is suitable without alterations. Any alterations must only be made by a
qualied electrician.
• The cord should not be extended or folded into coil during operation.
• Adapters, multi-socket strips and extension leads must not be used.
• Overloading could result in a risk of re.
Caution!
Before connecting to the power supply, check:
• The voltage meets requirements.
• The appliance uses an individual socket and does not share one with another electric appliance. A dedicated power protection switch
must be incorporated in the xed wiring in accordance with the wiring rules.
Selection of installation equipment
38
Cut out the work surface according to the following sizes.
L 900 mm
W 520 mm
H 60 mm
D 56 mm
A 875 mm
B 495 mm
X 50 mm (Min.)
• A minimum of 50 mm space shall be preserved around the hole.
• The thickness of the work surface must be at least 30 mm. Select heat-resistant work surface material to avoid larger deformation caused by
the heat radiation from the hotplate.
• The appliance must be well ventilated at all times. The air inlet and outlet shall not be blocked.
39
Observe the following sizes.
A 760 mm (= minimum safety distance between hotplate and cupboard above the hotplate)
B 50 mm
C 20 mm
D Air intake
E 5 mm (= minimum for air exit)
• The induction hob must be well ventilated and the air inlet and outlet at the bottom of the appliance must not be blocked. The fan situated at
the bottom of the hob must have sucient space and ow of fresh air at all times.
40
Seal the cut edge of the worktop with heat resistant silicone.
Place the appliance into the cut out. Push down rmly to t in place.
41
Preparation: Place the appliance on a stable, smooth surface (for example on the packaging). Do not apply force onto the controls protruding from
the appliance.
Adjusting the bracket position: Fix the appliance on the work surface by screwing 4 brackets on the bottom of hob after installation. Adjust the
bracket position to suit for dierent table top thicknesses.
42
The wires in the mains lead are coloured in accordance with the following code:
Brown and Black = L - Live
Blue and Grey = N - Neutral
Green/Yellow =
- Earth
The connection point must be placed in a position adjacent to the appliance so as to be readily accessible for an engineer in the event of a
breakdown.
43
For UK only
A Switched Fused Connection Unit to BS 1363 Part 4 is recommended.
The fuse must be rated at 32 Amps.
Any permanent electrical installation must comply with the latest I.E.E. Regulations and local electricity company regulations. For your own safety
a qualied electrician or contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC) should
undertake the electrical installation.
When you have installed the hob, make sure that
• The power supply cable is not accessible through cupboard doors or drawers.
• There is adequate ow of fresh air from outside the cabinetry to the base of the hob.
• The isolating switch is easily accessible by the consumer.
• The cable is not bent or compressed.
• The cable is checked regularly and replaced by authorised technicians.
IM_OBH39831_141028_V06.indb 28 10/28/14 2:44 PM
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for OK OBH39831 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of OK OBH39831 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 10,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info