475319

Mitsubishi WD-62628 Manual

94
Zoom out
Zoom in
Previous page
1/124
Next page
94 Chapter 7. Troubleshooting
General TV Operation
Symptom Suggested Solution
26. The message “Lamp will soon exceed...” keeps
displaying after the lamp has been replaced.
Reset the lamp reminder in the setup menu.
27. NetCommand unable to learn specific device
keys.
• DevicedoesnotuseIRformatforremotecontrolsignal.ITTandRFformats
cannot be learned.
• Roomlightingmayaffectthesignal.Havetheremotesveryclose(6inchesor
less) to the TV during Learning.
• IfusingaMitsubishiremotecontrol,makesureslideswitchisnotsettoTV
position.
• Some,butnotall,devicekeyfunctionscanbelearnedbyNetCommand.For
example, POWER and PLAY may be learned, but other functions may not
• Thesignalfromtheremotecontrolaynotbestrongenough.Insertfreshbatteries
and try Learning again.
Picture
Symptom Suggested Solution
1. PIP does not display a picture.
• MakesuretheV-Chiplockisoff.
• NotallinputscanbedisplayedasaPIP.
2. Digital channels do not appear in PIP. Normal PIP operation.
3. There is a large black or gray rectangle on the
screen.
The TV’s analog closed captioning has been set to “text”
mode in the Captions menu. Turn off because there is no text
information being broadcast.
4. You cannot see a picture when playing a VHS
tape.
• DisplaytheDeviceSelectionmenuandselectthecorrectVCR.
• CheckyourVCR’sowner’sguideforfurthertroubleshooting.
5. When viewing a stopped VCR, white lines are
rolling on the screen.
• TurnoffvideomutefortheVCR.
• Beginplayingthetape.
• ChangetheVCRinputtotheantennainput.
6. Screen is black when trying to view digital
channels or IEEE 1394 device.
The PerfectColor™ color balance has been incorrectly set.
Press VIDEO repeatedly until you see the PerfectColor option
and press ENTER.
7. A program recorded on your widescreen TV is
distorted when played on a 4:3 TV.
TV was set to Anamorphic when program was recorded.
Record programs in Cropped mode if playing back on a 4:3 TV.
Open the Record menu and select Cropped before making such
a recording.
8. Cannot see a picture from a DV Camcorder. DV formatting was not detected during automatic discovery,
so you must specify it manually. Open the Edit NetCommand
screen, select Change, then select the camcorder, Add, and in
the Name for 1394 Device screen, check mark the DV box.
9. DVCR analog/digital problems. If the tape is currently playing but no picture displays, there may
be a mismatch of the media with the display. Press DEVICE to
display the Device Selection menu. Press ENTER for the DVCR
device. If digital is selected, try analog, or if analog is selected,
try digital.
… 94 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-62628 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-62628 in the language / languages: English as an attachment in your email.

The manual is 7,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info