475319

Mitsubishi WD-62628 Manual

92
Zoom out
Zoom in
Previous page
1/124
Next page
92 Chapter 7. Troubleshooting
General TV Operation
Symptom Suggested Solution
1. The TV remote control does not work.
• Checkthatthebatteriesareinstalledcorrectly.
• Checkthattheselectedswitchissetto“TV.”
• Benomorethan20feetfromtheTVwhenusingtheremotecontrol.
• ProgramtheremotecontroltooperatetheTV(AppendixD).
2. The TV takes several seconds to respond.
• Itisnormalfordigitalchannelstotakelongertotunein.
• PressENTERafterachannelnumbertoavoiddelays.
• Usea4-digitnumberforanover-the-airdigitalchannel.
• Usea6-digitnumberfordigitalcablechannels(yourcableservicemustbeable
to recognize 6-digit channel numbers).
3. Cable provider needs information to start
CableCARD™ service.
On the remote control, press TV MENU and then enter the numbers 999
to display the Host ID and CableCARD™ ID information.
4. You cannot access a channel.
• UsenumberkeysinsteadofCHANNELup/down.
• Besurethechannelyouwanttoviewisinmemory.Seepage67.
• CheckthattheTVisturnedtothecorrectdeviceorantennaforthatchannelby
pressing the DEVICE button.
• MakesuretheV-Chiplockisoff.
• IfyoucannottunetoavirtualdigitalchanneleventhoughtheTVhasalready
memorized digital channels, tune to the channel number actually being used by
the broadcaster. The virtual channel will then be automatically added to memory.
5. On-screen displays appear each time you change
a function.
This is part of normal TV operation.
6. You cannot program the TV to turn on
automatically (timer function)
• TheTVmaybelocked.
• Theclockmaynotbeset.
• Atime-delayedrecordingmayhavestarted.
7. You have forgotten your V-Chip pass code. See Appendix C, Bypassing the V-Chip Lock.
8. V-Chip is not working.
• MakesurethatV-ChipisOn.
• IfV-ChipHoursarecurrentlysettodisabletheV-Chiplock,theV-Chipwillnot
block programming.
9. The TV will not turn on after being plugged in. If green light on front panel is blinking, wait for at least one minute for
the light to turn off, then press Power again.
10. TV functions do not respond to the remote control
or to front panel control and TV will not power off.
Use the System Reset button .
11. TV turned itself off and the light on the front panel
started to blink.
• MomentarypowerfluctuationcausedtheTVtoturnofftopreventdamage.Wait
for the green light to stop flashing and turn On again.
• IftheTVdoesnotstayturnedOn,usetheSystemResetbutton.Ifthishappens
frequently, obtain an AC line power conditioner/surge protector.
• Anunusualdigitalsignalmayhavebeenreceived,triggeringaprotection
circuit. Wait for the light to stop flashing and turn TV on.
12. Name options not available for some channels. Only memorized analog channels can be named.
13. When a device is selected from the Device
Selection menu, the screen is blue (no signal
source).
• Makesuretheselecteddeviceisturnedon.
• FromtheEditNetCommand®menuselectReviewsetting.Verifythatthedevices
are physically connected to the TV inputs as listed. If they are not, either change
the physical connections on the back panel, or select the Change setting on
the Edit NetCommand menu to change the TV NetCommand’s settings for the
connection.
• BeginplayoftheVCR.
… 92 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-62628 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-62628 in the language / languages: English as an attachment in your email.

The manual is 7,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info