Manual Mitsubishi WD-62628 (page 96 of 124) (English)

475319

Zoom out

Zoom in

1/124

96 Chapter 7. Troubleshooting

IEEE 1394 Devices

Symptom Suggested Solution

1. Excessive digital artifacts when viewing an IEEE

1394 device.

• TheIEEE1394cableistoolong;15feetbetweendevicesisthemaximum.

• TheremaybeaslowdeviceinthemiddleoftheIEEE1394network.Movethe

slow devices to the end so that connections for faster devices do not pass

through them.

2. D-VHS recordings for digital cable have

drop-outs (loss of picture or sound), or no

playback.

Digital cable signals on IEEE 1394 can exceed the data rate standards

supported by DVCR.

3. There is no audio and video from the IEEE 1394

device.

• Thedeviceisnotturnedon.Turnthedevicepoweron.

• Nomedia(tapeordisc)isinsertedintothedevice.

• Themediaisblank(hasnorecording).

• Theplaycommandfailed-Trypressingplayagainonthedevice’sremotecontrol

or front panel.

• Thedeviceisalreadyinuse(forexample,thedeviceiscurrentlyrecording).

• Thesourceiscopy-protectedorviolatescopyprotection.

• Thedevice’sdigitalvideosignalisnotsupportedbytheTV,asmaybethecase

with an IEEE 1394 signal from a computer. Use analog connections instead, if

available.

• Thedeviceisnotanaudio/videodevice.

• ToomanyotherdevicesarealreadycommunicatingoverIEEE1394.Removeor

stop some devices and try again.

4. The IEEE 1394 Device is not listed in the Device

Selection menu.

• ThedeviceisuncheckedintheReviewscreen.SelecttheNetCommandmenu.

Through Review, verify the device is checked.

• TheIEEE1394plugisdisconnectedorloose.

• TheIEEE1394DevicehasnotbeenpoweredOn.Turnon.

• Thedevicehasnotbeendiscovered.

• ThedeviceisnotanAudio/Videodevice

5. The IEEE 1394 device cannot be selected (is

grayed out).

The device may be busy, either recording or a peer-to-peer connection

has been established. Cancel the recording or peer-to-peer connection.

6. DEVICE MENU button does not display a menu.

• TheIEEE1394devicedoesnotprovideamenu.

• TheTVcannotsupportIEEE1394menus.

7. All IEEE 1394 devices disappear.

• TheconnecteddevicesmustnotbeinaloopthatreturnstotheTV.Makesurea

device is connected at the end.

• DisconnectallthecablesanddevicesfromtheTV.Replacethemonebyoneto

locate the problem device or cable

• UseSystemReset(frontcontrolpanel).

8. Cannot rediscover a deleted IEEE 1394 device.

• Thedevicehasbeendisconnected.Plugitin.

• ThedeviceisuncheckedintheReviewscreen.SelectNetCommandfromthe

Main menu, then select Review. Check the device.

• RemoveIEEE1394plug.GototheEditNetCommandmenu.DeletetheIEEE

1394 device. Plug the device in again so it can be discovered again.

9. An IEEE 1394 device has been plugged in but

does not appear in the Device Selection menu

(not discovered).

• TheIEEE1394connectiontotheTVoranotherdeviceisnotsecureorisloose.

• TheIEEE1394deviceisnotpoweredon.

• AdeviceintheIEEE1394chainisnotpoweredon.Turnonallthedevices.

• Thedevicediscoverycantakeaslongasaminutetoinitiate.

• IEEE1394cableistoolong(maximumof15feetbetweendevices).

• TheIEEE1394deviceusesanincompatibleprotocolandwillnotbediscovered

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-62628 in the language / languages: English as an attachment in your email.

The manual is 7,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Mitsubishi WD-62628 Manual

Product: