Manual Metabo TS-250 (page 18 of 49) (English, German, French, Italian)

494984

Zoom out

Zoom in

1/49

ENGLISH

To keep the set bevel tilt from changing

during cutting, it must be locked again by

the lock lever

(38).

Release lever for bevel tilt stop

The blade tilt setting has end stops at 0°

and 45°. For special bevel cuts (under-

cutting) the bevel angle can be

increased by 1.5° in both directions.

• Pull release lever (39) out and turn

into vertical position:

the blade bevel can now be set from

-1.5° to 46.5°.

• Set release lever (39) horizontal and

let engage in housing:

blade bevel is now adjustable from

0° to 45°.

Rip fence (for ripping):

For use as rip fence the long fence

extrusion (40) must be installed. It is

mounted on the guide extrusion at the

front of the saw table.

− For ripping the fence extrusion (40)

must be parallel with the saw blade

and locked in position by lock lever

(41).

− Wing nuts (42) for attaching the

fence extrusion. After loosening the

two wing nuts

(42), the fence extru-

sion can be removed and shifted:

Small edge:

− for cutting thin stock;

− when the saw blade is tilted.

Wide edge:

− for cutting thick stock (max. 77

mm).

Note:

To avoid stock jamming when

cutting along the rip fence:

slide rip fence all the way to the right

table edge and then back to the required

cutting width.

Mitre fence

The mitre fence (44) is inserted into the

table slot from the table’s front edge.

For mitre cuts the mitre fence turns to

60° in both directions.

For 45° and 90° miters positive stops are

provided.

To set a mitre angle: loosen locking han-

dle (43) by turning it counter-clockwise.

Risk of injury!

When cutting with the mitre

fence the handle must be firmly tight-

ened.

The auxiliary fence extrusion can be

taken off and reversed after loosening

knurled nut

(45).

Table side extension

The table side extension extents the

supporting surface, providing safe sup

port for larger workpieces.

• For table side extension adjustment

the lock lever (46) must be loos-

ened.

Risk of injury!

When cutting the handle must

always be firmly tightened.

Scale reading when using the rip

fence

On which scale the cutting width is read

depends on how the fence extrusion is

installed on the rip fence:

− Wide edge =

scale with black numerals on

white background.

− Small edge =

scale with white numerals on

black background.

For small cutting widths the table side

extension is not extended. The cuttings

width is read on the respective right-

hand scale at the rip fence's pointer:

− Wide edge: cutting width from 0 to

39 cm.

− Small edge: cutting width from 0 to

33 cm.

If larger stock is to be cut the table side

extension needs to be extended.

1. Move rip fence to the end position of

the respective right-hand scale.

2. Pull out table side extension and set

to desired cutting width. The cut

tings width is read on the respective

left-hand scale at the scale's pointer.

7.1 Assembly

Installing the crank for depth of cut

adjustment

• Attach crank (47) with Phillips screw

(48) to the handwheel.

4445

7. Initial Operation

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TS-250 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Metabo TS-250

Metabo TS-250 User Manual - Dutch, Portuguese, Spanish - 39 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo TS-250 Manual

Product: