494984
16
Zoom out
Zoom in
Previous page
1/49
Next page
16
ENGLISH
B
Danger! Risk of electric shock!
Do not expose tool to rain.
Do not operate tool in damp or wet
environment.
Prevent body contact with earthed
objects such as radiators, pipes,
cooking stoves, refrigerators when
operating this tool.
Do not use the power cable for pur-
poses it is not intended for.
A
Risk of personal injury and
crushing by moving parts!
Do not operate the tool without
installed guards.
Always keep sufficient distance to
the saw blade. Use suitable feeding
aids, if necessary. Keep sufficient
distance to driven components
when operating the electric tool.
Wait for the saw blade to come to a
complete stop before removing cut
-
offs, scrap, etc. from the work area.
Do not attempt to stop the saw
blade by pushing the workpiece
against its side.
Ensure the tool is disconnected from
power before servicing.
Ensure that when switching on (e.g.
after servicing) no tools or loose
parts are left on or in the tool.
Turn power off if the tool is not used.
A
Cutting hazard, even with the
cutting tool at standstill!
Wear gloves when changing cutting
tools.
Store saw blade in such manner that
nobody will get hurt.
A
Risk of kickback (workpiece is
caught by the saw blade and thrown
against the operator):
Always work with a properly set riv-
ing knife.
The riving knife and the saw blade
used must match: the riving knife
should be thinner than the kerf, but
thicker than the saw blade body.
Do not jam workpieces.
Make sure the saw blade is suitable
for the workpiece material.
Cut thin or thin-walled workpieces
only with fine-toothed saw blades.
Always use sharp saw blades.
If in doubt, check workpiece for
inclusion of foreign matter (e.g. nails
or screws).
Cut only stock of dimensions that
allow for safe and secure holding
while cutting.
Never cut several workpieces at the
same time – and also no bundles
containing several individual pieces.
Risk of personal injury if individual
pieces are caught by the saw blade
uncontrolled.
Remove small cutoffs, scrap, etc.
from the work area – when doing so
the saw blade must be at a com
-
plete standstill.
c
Drawing-in/trapping hazard!
Ensure that no parts of the body or
clothing can be caught and drawn in
by rotating components (no neck-
ties, no gloves, no loose-fitting
clothes; contain long hair with hair-
net).
Never attempt to cut any workpieces
which contain
ropes,
strings,
cords,
cables or
wires, or to which any of the
above are attached.
A
Hazard generated by insuffi-
cient personal protection gear!
Wear hearing protection.
Wear safety glasses.
Wear dust mask.
Wear suitable work clothes.
When working outdoors wearing of
non-slip shoes is recommended.
A
Risk of injury by inhaled wood
dust!
Dust of certain timber species (e.g.
beech, oak, ash) can cause cancer
when inhaled. Work only with a suit-
able dust collector attached to the
saw. The dust collector must comply
with the data stated in the technical
specifications.
Ensure that as little as possible
wood dust will get into the environ-
ment:
remove wood dust deposit in the
work area (do not blow away!);
fix any leakages on the dust col-
lector;
ensure good ventilation.
A
Hazard generated by modifica-
tion of the machine or use of parts
not tested and approved by the equip
-
ment manufacturer!
Assemble tool in strict accordance
with these instructions.
Use only parts approved by the
equipment manufacturer. This
applies especially for:
saw blades (see “Technical
Specifications” for stock nos.);
safety devices (see “Technical
Specifications” for stock nos.).
Do not change any parts.
A
Hazard generated by tool
defects!
Keep tool and accessories in good
repair. Observe the maintenance
instructions.
Before every use check tool for pos-
sible damage: before operating the
tool all safety devices, protective
guards or slightly damaged parts
need to be checked for proper func
-
tion as specified. Check to see that
all moving parts work properly and
do not jam. All parts must be cor
-
rectly installed and meet all condi-
tions necessary for the proper oper-
ation of the tool.
Damaged protection devices or
parts must be repaired or replaced
by a qualified specialist. Have dam
-
aged switches replaced by a service
centre. Do not operate tool if the
switch cannot be turned ON or OFF.
Keep handles free of oil and grease.
A
Risk of injury by noise!
Wear hearing protection.
Make sure the riving knife is not
bend. A bent riving knife will push
the workpiece against the side of the
saw blade, causing noise.
A
Danger from blocking work-
pieces or workpiece parts!
If blockage occurs:
1. Switch machine OFF.
2. Unplug mains cable.
3. Wear gloves.
4. Clear the blockage using a suitable
tool.
3.3 Symbols on the machine
Information on the nameplate:
(22) Manufacturer
(23) Serial number
(24) Machine designation
(25) Motor specifications (see also
"Technical specifications")
(26) Year of make
(27) CE-mark – This machine con-
forms to the EC directives as per
Declaration of Conformity
23
24
25
26 27
29
22
28
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo TS-250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TS-250 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Metabo TS-250

Metabo TS-250 User Manual - Dutch, Portuguese, Spanish - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info