494984
17
Zoom out
Zoom in
Previous page
1/49
Next page
17
ENGLISH
3.4 Safety devices
Blade guard
The blade guard (31) protects against
unintentional contact with the saw blade
and from chips flying about.
Always have blade guard installed dur-
ing operation.
Riving knife
The riving knife (30) prevents the work-
piece from being caught by the rising
teeth of the saw blade and being thrown
against the operator.
Always have the riving knife installed
during operation.
Push stick
The push stick (32) serves as an exten-
sion of the hand and protects against
accidental contact with the saw blade.
Always use the push stick if the distance
between saw blade and rip fence is less
than 120
mm.
Guide the push stick at an angle of 20°
… 30° against the saw table's surface.
When the push stick is not used, it can
be hung to the holder provided at the
base's side.
Replace push stick if damaged.
Precision adjustable bevel tilt from -
1.5 ° to 46.5°.
Simple release of bevel tilt stop from
0° to -1.5° and 45° to 46.5°.
Steplessly adjustable depth of cut 0
– 77 mm.
All operating elements are located
at the machine's front.
An electronic motor protection shuts
the motor off when it is locked (e.g.
by a blocked saw blade).
Electronic softstart for extended
motor life.
An undervoltage relay prevents the
machine from starting up when
power is restored after a power fail
-
ure.
Compact design for quick and easy
transportation.
Mitre fence and rip fence are stand-
ard delivery.
Saw blade and holder with cable
storage.
Pull-out table side extension.
Lower saw blade fully.
Set saw blade bevel tilt to 0° and
lock with lock lever.
Remove add-on parts (blade guard,
dust extraction).
If possible use original carton for
shipping.
A
Crushing hazard
Use handles provided on sides
of table to carry the machine (33).
Lock pulled-out table side extension
with lock lever.
A
Caution!
Do not carry the machine at the
guards, table side extension or oper-
ating elements!
ON/OFF switch
To stop = press upper switch button
(34).
To start = press and hold lower
switch button
(35) for 1 - 2 seconds.
3
Note: version 10
In the event of an overload a thermal
overload protection will trip. After only a
few seconds the machine can be
restarted. To restart, first press the
Reset button
(36), then the Start button
(35).
Note: from version 11
An electronic motor protection by over-
current detection shuts the motor off
when it is locked (e.g. by a blocked saw
blade). To restart, press the Start button
(35).
Note:
In the event of a power failure an under-
voltage relay trips. This prevents the
starting of the machine when power is
restored. To restart, press the Start but
-
ton (35).
Handwheel for setting the depth of cut
The depth of cut can be adjusted by
turning the handwheel
(37).
Bevel tilt lock lever
By releasing the lock lever (38) the saw
blade can be tilted from -1.5° to 46.5°.
(28) Waste disposal symbol – the
machine can be disposed of
through the manufacturer
(29) Dimensions of permissible saw
blades
30 31
32
4. Special Product Features
5. Transportation
33
6. Operating Elements
35
34
36
37
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo TS-250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TS-250 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Metabo TS-250

Metabo TS-250 User Manual - Dutch, Portuguese, Spanish - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info